Answered: Determine the strain if stress value is…

Engineering

Civil Engineering

Determine the strain if stress value is 33 MPa and modulus of elasticity is 80 MPa

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: 4. The horizontal bar shown is supported by a pin at A and two rods with identical length. Determine…

Q: 5. A metallic top-hat stringer reinforced wing skin (function of the material A=150) has a width of…

A: The function of the material = 150Width =1.5 mUnsupported length =0.5 mApplied compressive load =120…

Q: 2.Discuss elastic region in a tensile test and shear test. It is always linear. What is engineering…

Q: Q4. A 3 m long composite beam (perfectly bonded) is subjected to external loads V and P as shown in…

Q: The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P =…

Question

Determine the strain if stress value is 33 MPa and modulus of elasticity is
80 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Determine the value of stress if modulus of elasticity is 62 MPa and strain value is 0.0025
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
7. A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and Poisson's ratio of 20 GPa and 0.30 respectively. Calculate: a) the normal stress in the rod. b) the lateral strain in the rod. c) the change in diameter of the rod when the load is applied
solve the given problem and show complete fbd and geometry of deformation
Please show complete solution
(a) Determine the elastic strain when a stress of 80 MPa is applied to the model (rheological ) shown below. (b) Compute the total strain after a month (30 days). 5. 20 GPa |200 GPA.days 40 GPa | 300 GPA.days
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
Find the modulus of elasticity Stress=2 MPa Strain=0.1
A steel rod with a cross-sectional area of 188 mm2 is stretched between two fixed points. The tensile load at 23°C is 6,332 N. What will be the stress at -15°C ? Assume a = 11.7 x 10-6 m/(m.°C) and E = 198 GPa. Answer must be in MPa.
STRAIN
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?