2) Member (1) is a solid 50-mm diameter cylinder made from Am1004-T61 magnesium [E₁ = 44.7 GPa, a₁ = 26 x 10%/°C]. The cylinder is placed in the clamp when the temperature is T₁ = 20°C. Two 304- stainless steel solid carriage bolts (2) [E₂ = 193 GPa, a₂ = 17 x 10°C] hold the cylinder snug with negligible force against the rigid jaws of the clamp, and each have a diameter of 10 mm. Determine: a) the force in kN in the cylinder when the temperature rises to T₂= 130°C [Ans. to check: F=0.904 kN]

2) Member (1) is a solid 50-mm diameter cylinder made from Am1004-T61 magnesium [E₁ = 44.7 GPa, a₁ = 26 x 10%/°C]. The cylinder is placed in the clamp when the temperature is T₁ = 20°C. Two 304- stainless steel solid carriage bolts (2) [E₂ = 193 GPa, a₂ = 17 x 10°C] hold the cylinder snug with negligible force against the rigid jaws of the clamp, and each have a diameter of 10 mm. Determine: a) the force in kN in the cylinder when the temperature rises to T₂= 130°C [Ans. to check: F=0.904 kN]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

! Engineering Management ! Make an example of a QUALITY PLAN. Civil Engineer
Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds for the full capacity the 125x100x10mm angle tension member as shown below. Assume that the member is subjected to repeated stress variations making any connection eccentricity undesirable. Check the block shear strength of the member. Assume that the WT chord has sufficient strength to develop the weld strengths and the thickness of its web is 12mm. Use U=0.87 for class use and LRFD Method only. L125x100x10 V WT BOTTOM CHORD (please solve completely and neatly thank you so much) 12S
Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size. (b) Determine the bolt stiffness. Q # 3 15KN Rotating shaft Pillow block Metric (ISO) screw (c) Determine the stiffness of the 15 members. (d) Evaluate Yielding, Load and Joint Separation factor of safeties if the joint is permanently bolted. Steel 1cm Som Grey Cast Iron CLO-3, PLO-2
If the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mm
Determine the maximum factored load P, that can be carried by the connection shown in the Figure P7. 1. The weld is 6 mm fillet weld. All structural steel is A36. E70 electrode is used
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…
Q.2. The rigid bar AB, atrached to two verti cal rods as shown in Fig (e), is horizontal before the lead p is applied. If the load pe so kN, ditermine its Vertical mmovement. Aluminum Steel A300 mm 200 G A500 mm R-70 GN -3m- Fig (2)
Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material :fy = 480 MPa, fu = 560 MPa, Members are S235) a Section a-a 10 mm 10 cm P { =37.14 mm 5 cm 16 mm Gusset Plate a
Complete solution pls
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
2. The figure shown is bolted with a diameter of 22mm. The inner plate material is 12mm x 315mm and the outer plate material is 9mm x 315mm. Assume hole diameter is 2mm larger than the bolt. T/2 T/2 F, = 345MPA, F, = 450MPA, F, = 207MPA, F, 1.2F, for bearing type connection. F, a friction type connection. = 117MPA for 45mm 75mm T/2 a. Determine the tensile capacity of the plates if it is a bearing type connection. b. Determine the tensile capacity of the plates if it is a friction type connection. c. Compute the minimum theoretical length of the lap if it is a bearing type connection. 75mm T/2 75mm 45mm A в А