*19-44. The pendulum consists of a slender 2-kg rod ABand 5-kg disk. It is released from rest without rotating.When it falls 0.3 m, the end A strikes the hook S, whichprovides a permanent connection. Determine the angularvelocity of the pendulum after it has rotated 90°. Treat thependulum's weight during impact as a nonimpulsive force.0.5 m0.2 m0.3 m

Consider v1 as the initial velocity of the pendulum, d as the distance between point S and point A.…

Answered: *19-44. The pendulum consists of a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

stion 5 The 20-kg wheel has a radius of gyration ko = 400 mm where O is the center of the wheel. If the wheel is subjected to a moment, M = (2t) N.m, where t is in seconds, determine its angular velocity when t- 4s starting from rest. Assume the wheel is subjected to rotation only (no translation). OA 16.0 rad/s B. 10.0 rads oc 8.0 rad/s 0 5.0 rad/s
The 18-kg rod AB is pin-connected at A and subjected to a couple moment of M =15 N- m The rod is released from rest when the spring is unstretched at 0 = 30°. As the rod rotates, the spring always remains horizontal, because of the roller support at C. (Figure 1) Determine the rod' s angular velocity, measured clockwise, at the instant 0 = 60°. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. vec rad/s k = 40 N/m 0.75 m M = 15 N- m
The system is made up of the 1-m, 6.5-kg uniform rod AB and the two uniform disks (each of 0.19 m radius and 1.5 kg mass). If the system is released from rest when = 80°, when rod AB has just become horizontal, determine the coefficient C in the expression Cw² which is the kinetic energy of rod AB at this instant. Assume the disks roll without slipping. Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. AB' Take g= 9.81 m/s². A-L B m Your Answer: Answer
The 10-kg uniform cylinder is pin supported at its center O. The square isacted upon by a constant force F = 10N and a constant couple moment M = 10 Nm.If the disk starts from rest, determine1) The reactions at the pin O and the angular acceleration of the disk2) The number of revolutions it must take to attain an angular velocity of 10 rad/s
SOLVE USING PRINCIPLE OF WORK AND ENERGY
The 45-kg reel has a radius of gyration about its center O of ko = 220 mm. If it is released from rest, determine the total external work done to it when its center O has traveled 6.6 m down the smooth inclined plane (with angle = 35°). Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point, and proper SI unit. Take g = 9.81 m/s². 0.4 m 0.2 m²
At the instant shown, the spring is un-deformed. Determine the change in potential energy if the 20 kg disk (with radius of gyration kG = 0.5 m) rolls 2 revolutions without slipping. k= 200 N/m 3 m/s datum 0.3 m M = 2 Nm 30° O 1791 J O -1791 J O 1051 J O 1421 J O E) None of the above
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
The system is made up of the 1-m, 6.7-kg uniform rod AB and the two uniform disks (each of 0.10 m radius and 2.2 kg mass). If the system is released from rest when 0- 55", when rod AB has just become horizontal, determine the angular velocity of rod ABin rad/s. Assume the disks roll without slipping. Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. Take g= 9.81 m/s?. 1m
The uniform 80 kg slender rod is at rest in the position shown when P = 450 N is applied. Determine the value of angular velocity, w2 the rod if L1 = 5.5 m and L2 = 6.5 m. A L L2 L1 B
The 27-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r = 0.5 m. When the wheel is subjected to the constant force F = 354 N, applied to the wheel's center axle at an angle = 6°, it starts rolling from rest. Determine the wheel's angular velocity W (in rad/s) after 3.2 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². F 0 Your Answer: Answer
The 21-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.5 m. If it is subjected to the constant moment M = 78 N•m and is released from rest from the position as shown, determine its angular velocity w (in rad/s) when it has rotated 45°. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s2. `L MV Your Answer: Answer

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS