i need the answer quickly 19. Which A/D converter is considered to be simplest, fastest and mostexpensive?a) Servo converterb) Counter type ADCc) Flash type ADCd) All of the mentioned20. The flash type A/D converters are called asa) Parallel non-inverting A/D converterb) Parallel counter A/D converterc) Parallel inverting A/D converterd) Parallel comparator A/D converter21. What is the advantage of using flash type A/D converter?*a) High speed conversionb) Low speed conversionc) Nominal speed conversiond) None of the mentioned22.Drawback of counter type A/D convertera) Counter clears automaticallyb) More complexc) High conversion timed) Low speed23.Calculate the conversion time of a 12-bit counter type ADC with 1MHZclock frequent to convert a full scale input?a) 4.095 usb)4.095msc) 4.095sd) None of the mentioned24.A 12 bit dual ramp generation has a maximum output voltage of +12v.'Compute the equivalent digital number for the analog signal of +6v.a) 1000000000b) 10000000000c) 1000000000000d) 100000000000

Note :- As per guidelines,we are supposed to answer only 3 questions. So I request you to please…

19. Which A/D converter is considered to be simplest, fastest and most expensive? a) Servo converter b) Counter type ADC c) Flash type ADC d) All of the mentioned 20. The flash type A/D converters are called as a) Parallel non-inverting A/D converter b) Parallel counter A/D converter c) Parallel inverting A/D converter d) Parallel comparator A/D converter 21. What is the advantage of using flash type A/D converter? a) High speed conversion b) Low speed conversion c) Nominal speed conversion d) None of the mentioned

19. Which A/D converter is considered to be simplest, fastest and most expensive? a) Servo converter b) Counter type ADC c) Flash type ADC d) All of the mentioned 20. The flash type A/D converters are called as a) Parallel non-inverting A/D converter b) Parallel counter A/D converter c) Parallel inverting A/D converter d) Parallel comparator A/D converter 21. What is the advantage of using flash type A/D converter? a) High speed conversion b) Low speed conversion c) Nominal speed conversion d) None of the mentioned

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
What is RG rating of coaxial cable. Please give me detailed information. Don't copy previously given Answer
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
When using an oscilloscope for testing engine management systems, what is an attenuator used for? In your answer provide an example of when an attenuator should be used. (5 - 10 words)
i need the answer quickly
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.
Hey see
i need the answer quickly