18.4 A homogeneous disk of weight W = 6 lb rotates at the constant rate @₁ = 16 rad/s with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate @2 = 8 rad/s. Determine the angular momentum H₁ of the disk about its center A. Z y D 12 in. Fig. P18.4 C 12 in. r = 8 in. A B 9 in. 9 in. E x

18.4 A homogeneous disk of weight W = 6 lb rotates at the constant rate @₁ = 16 rad/s with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate @2 = 8 rad/s. Determine the angular momentum H₁ of the disk about its center A. Z y D 12 in. Fig. P18.4 C 12 in. r = 8 in. A B 9 in. 9 in. E x

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 6.169 At the instant shown, bar AB rotates with a constant angular velocity WAB 24 rad/s. Letting L= 0.75 m and H= 0.85 m, determine the angular acceleration of bar BC when bars AB and CD are as shown, i.e., B parallel and horizontal. WAB
Can you explain the radius of gyration ? why is it 480mm for the rod & 120mm for the disk. How do we figure this out ? thank you
Two shafts the axes of which intersect but are inclined to each other at 20 degreeconnected by means of a universal joint. At what position in the rotation cycle of thedrive shaft (i) velocity ratio will be maximum, minimum and unity (ii) the accelerationis maximum?
A 6-lb homogeneous disk of radius 3 in. spins as shown at the constant rate w1 = 60 rad/s. The disk is supported by the fork-ended rod AB , which is welded to the vertical shaft CBD The system is at rest when a couple M0 is applied as shown to the shaft for 3 s and then removed. Knowing that the maximum angular velocity reached by the shaft is 18 rad/s, determine (a) the couple M0) the dynamic reactions at C and D after the couple has been removed.
Problem 16.137 At the instant shown in (Figure 1), rod AB has an angular velocity WAB = 3.0 rad/s and an angular acceleration AB = 10 rad/s². The collar at C is pin-connected to CD and slides over AB. Figure 60° @AB αAB 0.75 m с 0.5 m B 1 of 1 Part A WCD= Determine the angular velocity of rod CD at this instant. Express your answer in radians per second to three significant figures. Enter positive value if the direction of velocity is counterclockwise and negative value if the direction of velocity is clockwise. IVE ΑΣΦΑ ↓↑ vec Submit Part B αCD = Request Answer Submit Determine the angular acceleration of rod CD at this instant. Express your answer in radians per second squared to three significant figures. Enter positive value if the direction of acceleration is counterclockwise and negative value if the direction of acceleration is clockwise. [Π ΑΣΦ Request Answer ? vec rad/s ? < rad/s² 8 of 8 Review
Two uniform cylinders, each of weight W=14 lb and radius r = 5 in, are connected by a belt as shown. Knowing that at the instant shown the angular velocity of cylinder A is 30 rad/sec counterclockwise, determine (a) the time required for the angular velocity of cylinder A to be reduced to 5 rad/sec, (b) the tension in the portion of belt between the two cylinders. *** Solve using the method of impulse-momentum *** B
A stationary horizontal plate is attached to the ceiling by means ofa fixed vertical tube. A wheel of radius aa and mass mm is mounted on a light axle ACAC that is attached by means of a clevis at AA to a rod ABAB fitted inside the vertical tube. The rod ABAB is made to rotate with a constant angular velocity ΩΩ causing the wheel to roll on the lower face of the stationary plate. Determine the minimum angular velocity ΩΩ for which contact is maintained between the wheel and the plate. Consider the particular cases ( aa ) when the mass of the wheel is concentrated in the rim, (b) when the wheel is equivalent to a thin disk of radius aa also extend the problem using Kinematic and Kinetic analysis
Only need A, B, and C please.
DYNAMICS OF RIGID BODIES
Solve correctly and by hand please
6
An automobile wheel test rig consists of a uniform disk A, of mass mÃ = 5000 kg and radius rÃ = 1.5 m, that can rotate freely about its fixed center C and over which the wheel of an automobile is made to roll. A wheel B, whose center and center of mass coincide at D, is mounted on a shaft (not shown) that holds D fixed while it allows the wheel to rotate about D. The wheel has diameter d = 0.62 m, mass mß = 21.5 kg, and mass moment of inertia about its mass center /D = 44 kg-m². Both A and B are initially at rest when B is subject to a constant torque M that causes B to roll without slip on A. M B d A If M = 1200 N·m, use the angular impulse-momentum principle to determine how long it takes to reach conditions simulating a car speed of 100 km/h. The automobile wheel test rig takes s to reach conditions simulating a car speed of 100 km/h.