18 m.D= 0.02 mA = 3.141 X 104m2E/D= 2 X 1042.5 mOpenAera = 0.75 m?37 mPondS.G 0.83H=2 X 103 Pa.sQuestion 2What will be Ep required, without friction? (J/kg)

Bernoulli's equation is used to find the relation between the heads of the fluid. It states that by…

Answered: 18 m D= 0.02 m A =3.141 X 10 m? E/D= 2…

18 m D= 0.02 m A =3.141 X 10 m? E/D= 2 X 104 2.5 m Open Aera = 0.75 m2 37 m Pond S.G = 0.83 u =2 X 103 Pa.s Question 2 What will be Ep required, without friction? (U/kg)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the total hydrostatic force on the conical stopper shown below? V cone =nr?h where r 3 is radius and h is the height of the cone. Atmosphere (S.G.)ie=1.26 30 cm 21 cm 15 cm 15 cm
Aparticle moving along a straight line has an acceleration which varies according to position as shown. If the velocity of the particle at the position x- -3 ft is v- 4 ft/sec, determine the velocity v whenx- 10 ft. a, ft/sec? 9 -3 4 8. 10 x, ft
What is the maximum time (in hours, nearest hundredths) a glider can achieve over the ground if it were to perform unpowered descent from an altitude of 4,011 m? Its weight = 2,663 N, Area = 16.1 m², and CD=0.011 +0.026C₁2. Assume SSLC (1.225 kg/m³) and cosy 1.
In a forklift, cylinder area 512mm^2 and pressure 584 N/mm^2 Calculate the mass( in tonnes)
Plz solve Subject : Engineering Mechanics
h 4m Zd d = h - th= th ? fentroid - center of pressure. water F₁ 3h F₂ =0.86) 7 M₁ = F₁-d₁ = @h²₁ A₁) d₁ M₂= F₂ · d ₂ (J₂h²₁₂A₂) d₂ H Solve for Ha № 0.86 =431m (1) How deep should the oil be So that there is no net horizental force on the platte? H= [16 F₁ = F₂ P₁ (B⋅4m) = P₂|(B⋅H) That=rcha - H 1 (m) - 4MH). H x4m 16 = 0.86 H² (2) Are the magnitudes of the moments about "the base of the plate equal ? Why?
24 kN/m 64 kN • m Dy В - 2 m 2 m 2 m
L V2 hg,strekli= f •5°2g + z, + hpompa.f 2g v? P2 +zz + hearbin,s + hg,toplam p.V.D Re = Pg pg 1.11 |6.9 -1.8 log Re hx.yerel =EKs Wmil hx,toplam= hx,sarekli + hx.yeret 3.7 2g Протра wỷ/2 ENPY = g Nsp H =-(wr,V2t – wr,V14) ý= 2nr,b,V,m = 2trzb2V2.n 2g/ pompa girişi (gH)³/4 Pg Wmil.B PB (WB Wmla PA WB (DR (D' WA From the experiments performed on the pump (pump A) in a laboratory, the following values at the best efficiency point were obtained; cm³ kg DA 3D 15 ст, НА 3 240 ст, Va%3D 1500 PA = 998 Na = 1800 rev / minute and ve NApompa = 0,91 ст3 HB 610 ст, Рв kg 998 m3 ve Vp= 4100' %3D It would be desirable to design a new pump (pump B) with values. Accordingly, which of the following is the revolution number of the new pump? 2051 rev / minute 2512 rev / minute 2196 rev / minute 2378 rev / minute 1969 rev / minute
In the below closed hydraulic system arrangement, the diameter of the piston P1 = 14 cm and the force applied F = 21 N, if the desired output force F2 = 279 N, then the diameter of the piston P2 must be equal %3D to m. F1 F2 D1 D2 O a. 0.51 O b. 5.10 O c. 72.90 O d. 51.03
P= ? Pa= ? Vュ=? %3D V2 = 2.5 m /s %3D D: 300 mm 3 m V, = 3 m/s D=usom 3m Uュ=? =200 mm Z354.5 そ:5
Drill pipes of 1000 meter original length which is between top drive drilling motor and bottom hole assembly (HWDP, collar and drill bit) is lowered into the well. The specification of drill pipe is as follows: • OD-200 mm, ID=175 mm, E = 50 GPa, G=77.2 GPa weight : drill pipe = 100,000 N, bottom hole assembly = 35,000N Before the bottom hole assembly touch the rock formation: a) Calculate the reaction force between drill pipe and top drive drilling motor b) Calculate the elongation of drill pipe After the bottom hole assembly rest/touch on the rock formation, the elongation of the drill pipe reduces by half. c) Calculate the reaction force between drill pipe and top drive drilling motor. d) Knowing that the top steel drill pipe rotates through two complete revolution. before the drill bit starts to operate, determine the maximum shearing stress caused in the pipe by torsion.
B7