A crate of mass m =rough ramp at a constant speed v by a motor with a powerinput of Pm = 2 kW. The ramp is angled at 0 = 40° withrespect to the horizontal, and the coefficient of frictionbetween it and the crate is u = 0,5. Find the crate's speedv up the ramp if the motor is 60% efficient.Р.5)50 kg is pulled up a%3Dт

Answered: Image /qna-images/answer/f672fca2-7858-4a55-a74d-8cb45efef1a5.jpg

A crate of mass m = 50 kg is pulled up a constant speed v by a motor with a pow 2 kW. The ramp is angled at 0 = 40° w. horizontal, and the coefficient of frictie a the crate is µ = if the motor is 60% efficient. 0,5. Find the crate’s spe«

A crate of mass m = 50 kg is pulled up a constant speed v by a motor with a pow 2 kW. The ramp is angled at 0 = 40° w. horizontal, and the coefficient of frictie a the crate is µ = if the motor is 60% efficient. 0,5. Find the crate’s spe«

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 75 pound object needs to be lifted vertically one foot. You bave a 2-inch diamcter piston actuator with a 12-inch stroke connected to a 50 psi source of presSurized air. The mass is restricted by a set of guide rails, which imit it to vertical motion, and which ase roller bearings with & friction coefficient of 0.002. Can the object be lifted? How long I will it take?
A vertical sliding gate is being submerged in a 10 meter water. The gate is 5m wide and 9 m high and weighs 50 kN. What vertical force is needed to just lift this gate considering that the Coefficient of friction between the guides and edges is 0.25 (Neglect Buoyant Force) Ans: 657 kN
There is a box with height 1.2 m, width 0.8 m and mass 50 kg. It contains a very expensive equipment, which cannot be tilted while moving. There is a rope connected to the top-right corner of the box that you can pull with. The static friction coefficient between the floor and the box is 0.4. Assuming the rope angle θ is 30 degrees and m/s2. a) Is it possible to move the box using the rope without tilting the box? (need to show details) b) What is the minimum force required to move the box on the floor?
: The cylinder shown in Fig. (2), Acytinder=7.012cm², has two pistons mounted, the upper one, mp1 =100kg, initially resting on the stops. The lower piston (mp2 =0kg) has 2kg water below it, with a spring (linear) in vacuum connecting the two pistons. The spring force is zero when the lower piston stands at the bottom, and when the lower piston hits the stops the volume is 0.3m?. The water, initially at 50kPa, V =0.00206m, is then heated to saturated vapor. Determine: (1) the initial temperature (2) the pressure that will lift the upper piston (3) The condition of steam when the lower piston hits the stops (4) the work done by the water (at saturated vapor state). Patm=101.325kPa Piston 1 stops Piston 2 H:0 Fig.2
If a 10 N force is used to compress a spring by 22 cm (i). What is the resulting spring constant? (ii). How much work is needed to compress the spring an additional 1.5 cm?
An elevator moves downward at a speed of 1 ft/s. If the total weight is 4500 lbf, find the cushionforce needed to stop the elevator in 2 inches. Use the rolling friction of 0.02 of the verticalweight
Blocks A and B have a masses of 150 kg and 280 kg, respectively. (Figure 2) The coefficient of static friction between A and B and between B and C is 0.290. The coefficient of static friction between the rope and peg E is 0.570. Pulley D rotates freely, and P = 27.0 N. If \theta = 60.0 degrees, what is the smallest magnitude, T, of tension, T, that causes block B to move? P A B E T
A sled of mass 500kg sits at rest on a rough slope that is inclined at 10* to the horizontal. The coefficient of friction between the slope and the sled is 0.3. The sled is held in place by a wire attached to a winch. The tension in the wire is TN. a) Find the maximum possible value of T. A load of mass mkg is added to the sled, and tension in the wire is increased to 5000N in order to pull the sled and load up the slop. Given that the sled and load are pulled a distance of 100m in 80seconds, b) Work out the value of m
I need an answer with a free body-diagram. Show all work as quickly as possible. Question: A wooden plank of negligible mass and length L = 2.8 m is used to keep in balance, horizontally, a small cube of mass 20.0 kg when applying a force F of 80.0 N at one end of the board. The distance, in meters, between the support point of the board and the position where find the cube is: a) 0.56 b) 0.80 c) 1.00 d) 1.12 e) 1.40
B7
A block and sphere are connected by a cord that passes over a pulley as shown. Neglect friction and assume the cord is massless. Take m1 = 2.00 kg, m2 = 7.65 kg, and ? = 49.0°. A triangular structure is oriented such that its base rests upon a horizontal surface, its left side is perpendicular to its base, and its right side forms an incline of angle ?. A pulley is attached to the structure's apex. Two objects are connected by a cord that passes over the pulley. A circular object labeled m1 is attached to the to the left end of the cord and hangs freely. A rectangular object labeled m2 is attached to the end of the cord and rests upon the incline. (a) What are the magnitude of acceleration (in m/s2) of the block and sphere? _____m/s2 (b) What is the tension (in N) in the cord? (Enter the magnitude.) ____N (c) What is the speed (in m/s) of each object 2.25 s after being released from rest? ____m/s (d)What If? If the incline under m2 is rough, what is the minimum value…
A 1.0 kg block is pushed 1.0 m at a con- stant velocity up a vertical wall by a constant force applied at an angle of 30.0° with the horizontal, as shown in the figure. The acceleration of gravity is 9.81 m/s². 1 kg 1 m Drawing not to scale. If the coefficient of kinetic friction between the block and the wall is 0.30, find a) the work done by the force on the block. Answer in units of I Answer in units of J 30° part 2 of 3 b) the work done by gravity on the block. Answer in units of J. Answer in units of N part 3 of 3 c) the magnitude of the normal force be- tween the block and the wall. Answer in units of N.