18150F = 25 kNA25200-2525100252550Calculate the maximum combined stress in the throat of the weld. The 9mm is the LEGsize. Note that the weld is on the Vertical sides only. All dimensions in millimeters.

M=F⋅e=25,000⋅150=3,750,000Nmm.

Answered: 18 150 F = 25 kN A 25 200 -25 25 100 25…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the three Mohr’s circles that describe the following state of stress.
Determine the required diameter (in inches) of rod ACif the allowable normal stress is 23.44 ksi and P = 6.6 kips. Round off the final answer to four decimal places.
Join two pieces of metal that are .045 and .045 thick. The joint is made with a triple row of MS20426 rivets. Use minimum edge distance and spacing. The Joint is 7 inches. Diameter of rivets = Length of rivets = Rivet Part Number = Number of rivets =
Hi I seem to be getting this wrong I have drawn this and submitted it but it says incorrect so I just really needed help on how to draw it the correct way Thanks!
this question is not for a grade. it is only a study question. submitting it is not a violation of the honor code
correct ans
The metal bar shown is subjected to a 4000 lb. tensile force. What is the tensile stress in the bar? 4,000 psi 20,382 psi 5,093 psi 40,500 psi
Please explain how you calculate for part a and part b. Thank you
The state of stress at a point on an element of material is shown. Let sigmaX= 49.0 ksi, sigmaY= 17.0 ksi, and Txy= 11.0 ksi. Use this information to represent the principle state of stress and maximum in plane shear stress. Plot the mohr circle and state sigmaX' and sigmaY' and Tx'y' with unit. Also draw the state of stress on the rotated element.
Please answer with explanation. I will really upvote
The pressure tank shown has a 0.375-in. wall thickness and butt-welded seams forming an angle ß = 20° with a transverse plane. For a gage pressure of 87 psi, determine the normal stress perpendicular to the weld and the shearing stress parallel to the weld. (Round the final answers to their nearest whole numbers.) 10 ft 5 ft + The normal stress perpendicular to the weld is The shearing stress parallel to the weld is psi. psi.
If in a tensile loading application, the factor of safety for one member is set as FS = 2.2 based on the material's tensile (failure) strength as 6 (fail) 614 MPa, then the load member's allowable stress in this application will be: MPa. Calculate your answer to 1 decimal place. (allow) =

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

18 150 F = 25 kN A 25 200 -25 25 100 25 25 50 Calculate the maximum combined stress in the throat of the weld. The 9mm is the LEG size. Note that the weld is on the Vertical sides only. All dimensions in millimeters.