170 50 60 50- 2) 165 175 65

Q: Name: Q1/ Give the Name of plans in the Image? The anatomical planes www.free-anatomy-quiz.com Q2/…

A: Plane A -Frontal PlanePlane B -MidSagittal Plane Plane C - Transverse Plane

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: -Which of the following options represents the stereoscopic shape of the projections in the figure?…

A:

Q: rection: Locate the center of gravity in figures A & B by putting a dot or a point in each of the…

A: centre of garvity is the point where the gravitational force is acting through

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: TS DIAGRAM

A:

Q: For the following figure assume the box as 10 mm and sketch the following view using CREO PARAMETRIC…

A:

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: What is the center of gravity in this figure?

A: given; center of gravity on given figure?

Q: Q2: Select physical dimensions and produce engineering parts list You are to select two deep groove…

A: The Answer is below

Q: The front and top views are given. Use this to create the missing side view. Note the front view is…

A: The required missing side view for A and B and the missing lines for C are drawn below.

Q: To make the 3d sketch for each of the frames which contain the views in the plan

A:

Q: Direction: Locate the center of gravity in figures A & B by putting a dot or a point in each of the…

A:

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: Given the views below, sketch its isometric figure.

A:

Q: Given the left and front views, sketch the top view.

A: The problem is easily done with the help of orthogonal projection. first try to imagine the 3D view…

Q: Pls provide the sectional view below

A:

Q: LO 10 $ 25 R 3 R6 R 12 30

A:

Q: Q2 (a) Figure Q2 (a) shows two vectors FA and Fa represent the forces exerted on the pulley by the…

A:

Q: DRAW THE MULTIPLE VIEW

A: The given view is in isometric view

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: Why cos(60 if I don't see that angle in the figure

A: This question can be solved by labelling angles.

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: PS Find Ter, Cower , P for Figure lower 1 below 9, 一E 2.

A:

Q: Top View Front View Right side View

A: according to the given details in the question, the Drawing of the figure is shown below. as…

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: Sketch the isometric figure of the given views below. Thank yo

A:

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: Draw the multiple view

A: Given isometric view

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: Given the top and front view create a section view.

A: Given: The top and front view, To create a section view.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.