16. A sling shot was released in a vertical direction using a rubber band having an equivalent spring constant of 2N/mm. If the deflection of the rubber band amounts to 10cm and the mass of the ston is 29g, determine the maximum height (above the undeflected position of the sling) the shot ca reach. a. 35.0506m b. 44.1703m c. 44.2203m d. 48.4413m

16. A sling shot was released in a vertical direction using a rubber band having an equivalent spring constant of 2N/mm. If the deflection of the rubber band amounts to 10cm and the mass of the ston is 29g, determine the maximum height (above the undeflected position of the sling) the shot ca reach. a. 35.0506m b. 44.1703m c. 44.2203m d. 48.4413m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Free
Lm. mL 600 Problem 56. Two rods, each of length 1-0.5m and mass m₁ = 1 kg, are joined together by hinges as shown. The bottom end of the left rod is connected to the ground, while the bottom end of the right one is connected to a block of mass m₂ = 2 kg. The block is then released to a position where the rods form a 60° angle with the horizontal plane. Friction is negligible. a) Find the velocity of point A as it hits the ground. b) Find the acceleration of mass my at that moment.
In the position shown in figure shown, the block of mass 100 kg just contacts the free end of the spring with constant k-6000N/m (a) If the block is released instantaneously with zero initial velocity, find the m lection of the spring (b) Find the max deflection, if the block is very gradually lowered onto spring. 100kg Free end ANS: a.)|| m b.) m (two decimal places)
An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. a.) Which Tension is larger, Ta or Tb? Explain b.) What is the angle of contact in radians? c.) What is the value of the ratio Ta/Tb? Please answer these , with FBD and solutions please.
Learning Goal: To determine an I-beam's maximum bending moment, moment of inertia using the parallel-axis theorem, and the maximum stress at a given location using the flexure formula. As shown, I-beam ABC supports a sign that weighs S = 30 lb . The I-beam is 24 in. long and is further supported by a rod that is attached 18 in. from the wall. Assume that all forces acting on the I-beam act along its centroid and that the I-beam's weight is negligible. Let the dimensions of the I-beam be w = 4 in., g = 0.8 in., h = 2.9 in., j = 1 in., c = 6 in. c A ·a b B Part A - Free-body diagram of beam ABC S C H j- W h Before the problem can be analyzed, a free-body diagram must be drawn to understand the forces and reactions that act on the I-beam. Draw the free-body diagram of beam ABC. A free-body diagram includes the forces acting on the object, in this case the beam. Start your vectors at the black dots. You will not be graded on vector length. Ignore all reaction forces in the x direction, and…
com/c/MTIXNZA5MTY31 TOWMDU3MTQXNZ15/details Tripie Beam Balance Practice Record the mass show on each balance. Remember to include both the value on the beams and the unit of measurement. 0 10 20 30 40 50 60 70 80 06 100g 100 200 300 400 500 g 10g 1. 0. 10 20 30 40 50 60 70 80 90 100g
Please answer all parts or leave for someone else to answer.
15. A 4,900N block is resting on a 30° inclined plane with a coeff of friction of 0.30. What is the required horizontal force P that prevents the block from sliding? a. 1,017N c. 4,236N b. 1,158N d. 5,212N
IDENTIFICATION It is an approximation of a force applied over a very small area. It is a slender bar that carries transverse loading. The goal of _______ is to determine the shear force V and the bending moment M at every cross section of the beam. For a shaft subjected to a torque, each cross section rotates as a rigid entity about the ____ of the shaft. It is the distributed load that acts over a very narrow area.
In the following cantilevered beam impact configuration pictured in Fig. 1, Determine: 1. The value of the equivalent spring K. 2. The values of the maximum impact force Fmax for weight heights ranging between h = 0 to 2 m. 3. Plot the maximum impact force Fmax as a function of the weight height h. 4. Plot the maximum force Fmax versus the maximum spring displacement Smaxwhen the weight height varies between h = 0 to 2 m. The beam has a resctangular cross section area. E = 70 GPa a = 10 cm b = 2 cm L = 1 m M = 5 kg g= 9.81 m/s² b of tat M h = 0-2 m K L Fig. 1 Cantilevered beam
5. Please show your complete solution. Please typewritten for upvote.
A spring of negligible mass is compressed between two masses on a frictionless table with identical sloping ramps at each end. The masses are released simultaneously. The masses have the same volume, but the density of M1 is greater than that of M2. M1 M2 wW (Select Greater than, Less than, or Equal to.). Greater than v The final height up the ramp reached by M1 is ... the height reached by M2. Equal to on M1. v The (magnitude of the) force exerted by the spring on M2 is ...the force it exerts v The duration of the force exerted by the spring on M1 is the time the force acts Equal to on M2. ...