In the following cantilevered beam impact configuration pictured in Fig. 1, Determine: 1. The value of the equivalent spring K. 2. The values of the maximum impact force Fmax for weight heights ranging between h = 0 to 2 m. 3. Plot the maximum impact force Fmax as a function of the weight height h. 4. Plot the maximum force Fmax versus the maximum spring displacement Smaxwhen the weight height varies between h = 0 to 2 m. The beam has a resctangular cross section area. E = 70 GPa a = 10 cm b = 2 cm L = 1 m M = 5 kg g= 9.81 m/s² of tat M h = 0-2 m K

In the following cantilevered beam impact configuration pictured in Fig. 1, Determine: 1. The value of the equivalent spring K. 2. The values of the maximum impact force Fmax for weight heights ranging between h = 0 to 2 m. 3. Plot the maximum impact force Fmax as a function of the weight height h. 4. Plot the maximum force Fmax versus the maximum spring displacement Smaxwhen the weight height varies between h = 0 to 2 m. The beam has a resctangular cross section area. E = 70 GPa a = 10 cm b = 2 cm L = 1 m M = 5 kg g= 9.81 m/s² of tat M h = 0-2 m K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the loaded beam shown below , Estimate the Reaction Values of supports
Total Length Of the beam L = 50 cm, Lı= 20 cm , L2 = 5 cm and self weight of beam = 5 N Load F1 = 1.8 N, F2 = 1.2 N, Experimental RA = 3.6 N, RB = 4.4 N L1 A
The 10 m long simply supported beam in Fig. Q3 is loaded as shown at a point 6m from left end. e (1) (ii) (iii) RA 10%N 10 kNm": Fig. Q3 Calculate the support reactions R₁ and RB. Macaulay's method is to be used to find slopes and deflections along the beam. Write a general expression for the bending moment to enable the solution. Calculate the vertical deflection at the load application point. The flexural rigidity of the beam, EI, is 100 MNm².
solve using simply supported beam not rigid support (hint meq and k formulas are on the front cover of the book)
Use answer from first part without spring to build onto next part, thanks.
SITUATION 1: A T-beam is simply supported and is used to carry a uniform load of 20 kN/m. The beam is 4m long and has the following properties of 5 the T-beam are as follows: bf=500mm; tf=D100mm tw=200mm; dw3300mm PAV
Problem 7.65 - Enhanced - with Hints and Feedback Figure 3 m 6 m 12 kN/m 4 of 15 ■Review Draw the moment diagram for the beam. Follow the sign convention. Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. Note 1 - Draw a vertical line to denote local maximum or minimum. Note 2 - The curve you choose from the drop-down is only a pictorial representation of a real quadratic/cubic curve. The equation of this curve is not mathematically equivalent to the correct answer. Consequently, slopes at discontinuities and intercepts with the x-axis (if any) are not accurate. 1 of 1 ▸ View Available Hint(s) B الا 十四 A i ✓ ? 3 m 12 kN/m с 6 m M (kN·m) No elements selected 50 40- B 10:04 PM
A uniform cantilever beam weighing 750-N has a smooth turning pulley attached to its free end. The pulley's mass is negligible compared to the beam's mass and may be ignored. As shown, the beam is loaded by a 1000-N block suspended by a wire rope passing over the pulley B and attached to a vertical wall. 2.5 m Cable 1000 N 0.3 m Questions: (a) Sketch a free-body diagram of the beam and pulley and label all exposed internal and external forces acting on the beam. (b) Determine all reactions exerted by the wall on the beam.
Note: The solution should not be hand written.
Answer the following and show your solutions: Problem Calculate for the support reactions of the beam shown ( 10 kN 8 kN/m 8 kN 15 kN.m hinge 75 2.5 m 2 m 3 m 3m 3 m 4 m
5 m 4m cg L... + B 2 m 3m GIVEN: BEAM MASS=45KG CENTER GRAVITY AT CG BOX MASS IS 90KG A = PIN B = ROLLER ASK: REACTION FORCES AT A & B
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. Determine the magnitude of the vertical force Ay for the cantilever beam, where w = 8 kN/m, M = 149 kN-m, and L = 5 m. "| 51 kN 25 KN 46 kN 43 kN 40 kN W L BO M X