150 x 250 mm rectangle beam carries a uniform distributed load of W kN/m over its entire span. The beam is freely supported at its ends. If the maximum allowable bending stress is 9Mpa and the maximum allowable shearing stress is 1Mpa. Calculate the safe uniform load W(kN/m) Calculate the value of maximum shear (kN)

Q: Determine the maximum tensile and compressive bending stresses in the beam shown. 4 kN/m 10 kN 6 m B…

A:

Q: The shaft shown is supported by at A and at C. If the material has an allowable bending stress of 24…

A: The bending equation is as follows, σy = MIWhere,σ = Bending stressy = Distance between neutral axis…

Q: 25 mm 160 mm Ain B 2 m 1m- Im For the beam and loading shown, consider the cross section nn. (a)…

A: Given data: P1=188 N P2=381 N b=25 mm d=60 mm

Q: The variable section beam has a uniform load w. If it is made of a plate with a constant thickness…

A: A beam of variable depth is given with constant thickness, b. The depth at the support is ho and…

Q: The internal shear force V at a certain section of an aluminum beam is 8.5 kN. If the beam has the…

A: Given data,  V = 8.5 kN a = 32 mm bf = 65 mm tw = tf = 7 mm d = 89 mm

Q: A B 400 mm 500 mm 20 mm 40 mm 7 kN/m 3 m 20 kNm 2.5 m 2.5 m 2 m 15 KN A T-beam with the…

A: Given Data Determine  a. Second moment of area of cross section.  b. Draw the SFD and BMD.  c.…

Q: The steel bearn has the cross section shown. The beam length is L = 7.7 m, and the cross-sectional…

A: Given Data:L=7.7md=360mmbf=205mmtf=12mmtw=6mmbending stress = 245Mpa

Q: H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of…

A: Given data,   Required: (a) the maximum tension bending stress at any location along the beam (b)…

Q: The uniform 2Mg bar is supported by a smooth wall at A and by a pin at B. Determine the diameter of…

A:

Q: The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the…

A: Solution:

Q: Required information Consider the beam and loading shown. Given: P= 8 kips 글 in. P 8 in. a 4 in. -…

A:

Q: A 500 Ib/ft uniform load w is applied to 6 ft rigid horizontal bar CA, pin supported at Cin single…

A:

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow =60 MPa.…

A:

Q: A simply supported wood beam with overhang is subjected to uniformly distributed load q. 9 с 200 mm…

A:

Q: Prob 2. Determine if the W14X22 beam will safely support a loading of w = 1.5 kip/ft. The allowable…

A:

Q: 6. Compute the maximum tensile and compressive bending stress for the simply supported beam with…

A: A we have to determine the maximum tensile and compressive bending stress

Q: A steel shaft is loaded as shown. Knowing that T₁ = 1000 N.m, T₂ = 1600 N.m, L=250 mm, d 40 mm, D =…

A: Given: T1 = 1000N .m T2 =1600 N.m, L = 250mm , d =40 mm, D = 45mm Required : Maximum shear stress…

Q: The steel beam has the cross section shown. The beam length is L = 30 ft, and the cross-sectional…

A:

Q: 2. The engine of the helicopter is delivering 600 hp to the rotor shaft AB when the blade is…

A:

Q: Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A: Given : Diameter of rod CD = 8mm Allowable average normal stress = 175 MPa Allowable Average shear…

Q: = 150 mm, d-370 mm, a 90 mm, and c= 35 mm. Section a-a is locate t section a-a, determine the…

A:

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

A:

Q: A simply supported wood beam with overhang is subjected to uniformly distributed load q. B TH 1 m-…

A:

Q: A simply supported wood beam that is 13.8 m long carries a 30 kN concentrated load at B. The…

A: Given data L = 13.8 m  a = 75 mm  b = 155 mm c = 40 mm d = 390 mm P = 30 KN So,  2L/3 = 2×13.8/3 =…

Q: For the shaft and loading shown, consider the n-n section. (a) Bending moment in section n-n |M| its…

A: Given:- A solid shaft is given with a diameter = 30 mm   The magnitude of the point load (P1) = 32 N…

Q: Determine the maximum shearing stress developed in each segment. For bronze, G = 36 GPa; aluminum, G…

A:

Q: 1, determine the magnitude of the shear stress in the beam at point 1, determine the magnitude of…

A:

Q: The internal shear force V at a certain section of an aluminum beam is 8.6 kN. If the beam has the…

A: Shear force (V) = 8.6 KN  Determine a. Shear stress at point H which is 37mm above the bottom…

Q: 6-121 A wood beam is reinforced with steel straps at its top and bottom as shown. Determine the…

A: Step 1: Calculate the Moment of Inertia (I) for the Wood Component using the formula: I=12bh3​ Step…

Q: A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown.…

A: A square box beam is made of 80 x120 mm s=50 mm allowable shearing force= 300N As the maximum…

Q: A WT265 x 37 structural steel tee shape beam is loaded and supported as shown. Determine the…

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions need to be solved.…

Q: The internal shear force V at a certain section of an aluminum beam is 10.6 kN. If the beam has the…

A:

Q: 1. For the W 21x 62 steel beam below determine the actual value of om in the beam and the maximum…

A: A simply supported beam at B and C, of length 30ft between B and C, with overhanging portion AB and…

Q: P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam…

A: b = 130 mm h = 200 mm  P = 25 KN w = 30 KN/m

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

A:

Q: The internal shear force V at a certain section of an aluminum beam is 10.5 kN. If the beam has the…

A:

Q: 4 ft C B ITI

A:

Q: are b = 145 mm, d = 350 mm, a = 85 mm, and c= 25 mm. Section a-a is located at x = 1.7 m from B. (a)…

A:

Q: An extruded aluminum beam has the cross section shown. Knowing that the vertical shear in the beam…

A: - Moment of area is given by QA ;Where ;Width = Thickness = 0.25 inch- Shear stress is given by ;

Q: (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At…

A: given-a simply supported beam carrying a point load at the distance of L/3 from support A…

Q: 8" H E = 36,000 ksi 5" Max Bending Stress: 1.25" TYP A simply supported beam has a symmetric cross…

A: Given Vmax = 800lb Mmax = 2400 ft-lb Required Maximum bending stress

Q: Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in…

A:

Q: A simply supported wood beam that is 9.0 m long carries a 35 kN concentrated load at B. The…

A:

Q: A simply supported wood beam that is 13.5 m long carries a 31 kN concentrated load at B. The…

A:

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.