15.How many clock cycles required to execute the program in the pipelined implementation using stalling? (Consider the control hazard only.) * [Program] il. i2. i3. LOOP: cmp %rcx,%rax 14. i5. 16. i7. EXIT: hlt irmov $0,%rax irmov $0,%rcx je EXIT inc %rax jmp LOOP 9. O 10 O 11 O 12

Q: Load register A (50H) with 20H and register B (20H), and then exchange their contents inside an 8085…

A: Write an 8085 assembly program to Load register A (50H) with 20H and register B (20H), and then…

Q: For our simple 4-stage RISC pipeline, we run a particular benchmark program and find that it has 19%…

A: Answer: We need to write the about the how work CPI in the pipelines so we will see in the more…

Q: To avoid the race condition, the number of processes that may be simultaneously inside their…

A: race condition is an undesirable situation that occurs when a device or system attempts to perform…

Q: We have a single stage, non-pipelined machine and a pipelined machine with 5 pipeline stages. The…

A: Hello studentGreetingsIn the realm of computer architecture and design, the choice between a…

Q: In what way would a procedure work if the RET instruction was left out?

A: The ret instruction transfers control to the return address located on the stack. This address is…

Q: It is requested to run an interrupt subprogram with rising edge triggering from RB0 port for 16f84…

A: I Have answered this question in step 2.

Q: Explain the instruction ( fliplr) with example? Your answer

A: FLIPLR COMMAND: The fliplr() command is used for the purpose of flipping the matrix left-right. The…

Q: The only reason RISCV uses registers to store variables for ALU operations instead of directly…

A: Please find the answer below :

Q: iven the assembly code: org 2000h xor a loop: out (40h), a inc a jp loop halt   Explain…

A: The Assembly language is defined and is used for the particular processor which is a low-level…

Q: What are the difference between the logical shift (the LSR instruction for ARM assembly) and the…

A: According to the information given:- We have to define the difference between logical shift (the LSR…

Q: Counter implementation using timer 1 module in timer mode.Each incremental value will have delay of…

A: #include <stdio.h>#include <stdlib.h>#include<pic16F877A>void Timer0Delay(void);…

Q: 7. How can you verify that the truth table obtained from the Multisim simulation matches the actual…

A: To verify that the truth table obtained from the Multisim simulation matches the actual output…

Q: 4. Design and implement a synchronous counter that counts 23⇒0⇒1⇒7 and back to 2 in a loop.

A: Here let's use D flipflop for designing the circuit. All the un mentioned state ie state 4,5 and 6…

Q: Explain in detail about concept of pipelining and state the pipeline stages elaborately with neat…

A: 1. Explain in detail the concept of pipelining and state the pipeline stages elaborately with a neat…

Q: Describe about loop unrolling for multiple-issue pipelines

A: Application-specific instruction set processors (ASIPs) are one of the popular processor design…

Q: The stage delays in a 4-stage pipeline are 800, 500, 400 and 300 picoseconds. The first stage (with…

A: As we Know ideal CPI (cycle per instruction) for pipeline instruction is  1. (CPI=1) Throughput =…

Q: Simulate "clock" in AVM with test bench parameters as set Add print statements to the test bench to…

A: I have tried this multiple ways, I am a bit desperate now. I have tried to make this clock in my…

Q: 160 and sters that a elay of 5 r stant clock

A:

Q: micro Control Flow Instructions and Timers Q.write an assembly program to generate a delay of 1.5…

A: Q.write an assembly program to generate a delay of 1.5 ms given the clock frequency of 12 MHz. Use…

Q: We have 2 designs D1 and D2 for a synchronous pipeline processor. D1 has 6 stage pipeline with…

A: To calculate the pipeline and non-pipeline cycle times for both designs, we can use the following…

Q: Solve for the Pipelining Clock cycle time if All 4 stages total time is 6.8 You have 4 number of…

A: The pipeline clock cycle time, also known as the pipeline cycle time or clock period, is the time it…

Q: There are several compelling explanations why edge triggers need to be employed in shift registers?

A: 1) A shift register is a type of digital circuit that stores and shifts data in a series of…

Q: VI. A given hardware contains 5 logic blocks that require 20ns, 35ns, 15ns, 50ns and 25ns…

A:

Q: ns resp tages a E is the Ictions

A:

Q: please i need corect answear Implement Lamport’s logical clocks with three process p1, p2, p3 where…

A: For master clock serve   #Python3 program imitating a clock server   from functools import reduce…

Q: The stage delays in a 4-stage pipeline are 800, 500, 400 and 300 picoseconds. The first stage (with…

A: Introduction  Given,   4‐stage processor (delays=800,500,400,300)   We are doing  some modifications…

Q: Create a 4 bit down counter that counts down from 9 to 0 and then count 10,11,12 and then back to 9.…

A:

Q: When any of the speed and rotate of motor run the others will not work.When the start button is…

A:

Q: Write the AVR Assembly instructions for a nested loop with 5 instruction cycles in the inner most…

A: An assembly instructions To a nested loop with 5 instruction cycles in the inner most loop Delays…

Q: Consider a non-pipelined machine with 5 stages of lengths 20 ns, 40 ns, 60 ns, 50 ns, 30 ns. Suppose…

A: Given :- 1) Five-stage non-pipeline machine 2) Length of stages is 20, 40, 60, 50, and 30. 3) Latch…

Q: Develop the Verilog Code to construct a Parallel-Access Shift Register, provide simulation code and…

A: The design of the shift register comprises of five input and single n-bit output. The design is…

Q: Describe all the different modes of operation in Programmable Interval Timer 8254 with its timing…

A:

Q: In a program 40% of the instructions have a CPI of 1, 25% have a CPI of 2, 20% have a CPI of 3, and…

A: Please give positive ratings for my efforts. Thanks.     ANSWER   Let the number of instructions be…

Q: 1A.What condition needs to be satisfied so that converting from a nonpipelied to a pipelined machine…

A: .What condition needs to be satisfied so that converting from a non-piped to a pipelined machine the…

Q: Categorize and Analyze MIPS ISA representing instructions format. Include MIPS Assembly examples in…

A: Instructions: MIPS ISA******************************************************1Instructions: MIPS…

Q: Please answer the following questions: 1. Why is it useful to have the ability to load a state in a…

A: State loading refers to the process of setting the initial state of a sequential circuit to a…

Q: Pipeline timing diagram for following Program and is there any data dependency. 5 stage pipieline.…

A: 5 stage pipieline.  ADD X1, X , X3OR    X4, X5, X6LDUR X5, [X6, #25]AND X9, X10, X11