Reorder the following instructions to run faster by reducing pipeline stalls. N = L * M P = Q + N R = S - T V = U + R Y = W * X K = Y * Z

Q: What is the final result for AL and BL after executing the sequential mnemonic opcode/operand…

A: Solution ::  Let's see first what is sequential mnemonic opcode/operand ? Answer ::  An opcode is a…

Q: Implement the following pseudocode in assembly language. Use short-circuit evaluationand assume that…

A: pseudo-code into assembly language, assuming for the val1 and X are 32-bit variables:

Q: Given a memory load instruction, "mov R0; [R1+1000]," please give the input that should be selected…

A: Given instruction: mov R0 , [R1 + 1000] , store content of (R1 +1000) to register R0 [R1 +…

Q: What is the minimum number of cycles needed to completely execute n instructions on a CPU with a k…

A: We need to find a formula to find the minimum number of cycles needed to completely execute n…

Q: Expanding opcodes make instruction decoding much easier than when it is not used.Trur or False.

A: Expanding opcodes represent a compromise between the need for a rich set of opcodes and the desire…

Q: Write an instruction that uses a segment override.

A: Instruction: A segment override is a one-byte prefix which is used to direct the current instruction…

Q: ing program using LOOP instruction: MOV AL,X MOV BL,X INC DL ADD AL,X INC DL ADD AL,X INC DL…

A: using emu8086: Rewrite the following program using LOOP instruction: MOV AL,X MOV BL,X INC DL ADD…

Q: Answer the given question with a proper explanation and step-by-step solution. LOOK AT THE OUTPUT.…

A: The correct answer for the above mentioned question is given in the following steps for your…

Q: solve using assembly language x86 processors and compatibles  Write a program that prompts the user…

A: the program is given below:-

Q: Amdahl’s Law My speedup factor is 6.  My new execution time after speedup is 5 seconds.  What was…

A: Execution time, often referred to as runtime or elapsed time, is the duration it takes for a…

Q: There is a method of writing to memory registers using something called a shift register, where data…

A: Here is the explanation of solution.

Q: What is the final result for AL and BL after executing the sequential mnemonic opcode/operand…

A: What is the final result for AL and BL after executing the sequential mnemonic opcode/operand…

Q: If the following code segment is pipelined, which are the instructions affected by data hazards and…

A: Answer related to finding hazards in the above instruction is stated in step 2 .

Q: 8.fast please in assembly  You are giving the before condition and an instruction. Give the after…

A: The question pertains to the manipulation of the stack in the context of the ret (return)…

Q: Write an assembly code in an inner loop to discover prime numbers from 3 to n in a loop by dividing…

A: Initialize the registers:Set ecx to 3 (starting number).Set edx to 2 (initial divisor).Print the…

Q: W rite a MIPS program to continuously generate the following series of integers: 1, 2, 3, 6, 9, 18,…

A: In this MIPS program, we will generate a series of integers, beginning with 1 and doubling the…

Q: What will be the value of AX (in Hexadecimal) after execution of the following instructions: MOV…

A: What will be the value of AX (in Hexadecimal) after execution of the following instructions: MOV…

Q: 13. Given the following Java loop, write the equivalent MIPS instructions. for (int i = 5; i < 75; i…

A: #working code li $t0, 75                   #t0 is constant 75 li $t1, 5                    #t1 is…

Q: Programming Project: For Loops Write an Assembly Language Program that produces the Times Table for…

A: Start.Declare two memory locations: 'result' to store the result and 'value' to hold a specific…

Q: Il rotate and shift instructions operate ) True O False L-7EH, BL=82H after execute ADD AL. O…

A: 1) All rotate and shift instructions operate with the carry flag directly. T his statement is True…

Q: 2) Write the equivalent instructions of (LOOP NXT).

A: The answer for the given question is below:

Q: The content of IR after the end of execution :for the next instruction is None of the choices 4620…

A: The solution to the given problem is below.

Q: Given clock = 10MHZ, what is instruction cycle? Please show how to generate 1 second delay. (You can…

A:

Q: Write a single instruction that converts an uppercase character in AL to lowercase but doesnot…

A: Single instruction: or al,00100000b

Q: Because of this, the means by which one instruction acquires its input data are independent of the…

A: The statement "Because of this, the means by which one instruction acquires its input data are…

Q: Implement the following pseudocode in assembly language. Use short-circuit evaluationand assume that…

A: The required assembly language uses the following decision making instructions: CMP instruction…

Q: A simple two-pass assembler does the following in the first pass: A. It allocates space for the…

A: Assembler is a program for changing over guidelines written in low-level get together code into…

Q: microprocessor Write an ALP to multiply the word 3421H by the double word 57412236H. Store the…

A: Code in ALP to multiply the word 3421H by the double word 57412236H :-

Q: In this implementation, each instruction is provided with its own data independently of how other…

A: Instructions with Multiple Variables and Many Data Variables (MIMD) Do operations on many data sets…

Q: We wish to execute a single LC-3 instruction that will subtract the decimal number 33 from R1 and…

A: we need to write LC-3 instruction that will subtract the decimal number 33 from R1 and put the…

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.