15.44 The 200 gram bullet has a constant speed relative to the rifle barrel of 2700 km/hr when it is in the position shown. In order to follow the target, the rifle is being rotated about the vertical axis at the constant rate 2 = 0.05 rad/s. The angle of inclination is constant at 0= 60°. Determine (a) the acceleration of the bullet, and (b) the y and z components of the force exerted by the rifle barrel on the bullet. Fixed point معلم 400 mm Bullet Urel= 2700 km/hr PROB. 15.44

15.44 The 200 gram bullet has a constant speed relative to the rifle barrel of 2700 km/hr when it is in the position shown. In order to follow the target, the rifle is being rotated about the vertical axis at the constant rate 2 = 0.05 rad/s. The angle of inclination is constant at 0= 60°. Determine (a) the acceleration of the bullet, and (b) the y and z components of the force exerted by the rifle barrel on the bullet. Fixed point معلم 400 mm Bullet Urel= 2700 km/hr PROB. 15.44

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q14. The collars are pin connected at B and are free to move along rod OA and the [C. (1 + cos 0)] m, curved guide OC having the shape of a cardioid, î where C = 0.3. The rod OA moves at a constant angular velocity 0 = 1.6 rad/s. Determine the magnitude of the acceleration (in m/s²) of the collars at the instant = 1.0 rad. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper SI unit. Your Answer: Answer B C =
The mass B is attached to the arm that rotates in the horizontal planeabout a pin in collar A. A motor in A keeps the angular speed of the arm constant at ˙ θ = 2.4 rad/s. Determine the velocity and acceleration of A as functions of the angle θ. Assume that vA = 0 when θ = 0. Friction and the mass of the rotating arm can be neglected.
Question: The rod OA rotates clockwise with a constant angular velocity of 6 rad/s. Two pin-connected slider blocks, located at B, move freely on OA and the curved rod whose shape is a limacon described by the equation r=200(2−cosθ)mm Part A: Determine the magnitude of the acceleration of the slider blocks at the instant θ = 105 ∘ Express your answer to three significant figures and include the appropriate units.
Collars A andB slide along the fixed right-angle rods and are connected by a cord of length L = 6.9 m. Determine the acceleration of collar B when y = 2.3 m if collar A is given a constant upward velocity vĄ = 1.61 m/s. The acceleration of B is positive if to the right, negative if to the left. Answer: aB = i m/s2
Show the complete solution that the degree is equal to 72.3. TY!
To speed up the unrolling of a telephone cable the trailer with the reel of cable starts from rest and is given a constant acceleration of 2.1 ft/sec². Simultaneously, the tow truck pulls the free end of the cable horizontally in the opposite direction with a constant acceleration of 3.4 ft/sec². If both vehicles start from rest at the same instant, determine the magnitude of the total acceleration of point A on the forward end of the horizontal reel diameter (a) just as the motion starts and (b) at a time t = 1.5 sec after the start of the motion. 3.4 ft/sec² 1/9 2.7' A 2.1 ft/sec²
● A 5 rad/s .2 rad/s² 3 ft X 3 rad/s -2 rad/s² B 2 ft 30⁰ с The robotic arm shown above has a fixed orange base at A and fixed length members AB and BC. Motors at A and B allow for rotational motion at the joints. Based on the angular velocities and accelerations shown at each joint (described with respect to the fixed frame): o Determine the velocity at the end effector at C o Determine the acceleration at the end effector at C
The figure shows a rigid link AB of length 2 m which rotates anticlockwise about a fixed point at A at a rate of 2 rad/s, but which is decelerating in its rotation at 1 rad/s². At the instance of time shown in the diagram, with the link AB at 60 degrees to the horizontal, what is the y-component of the absolute acceleration of point B? (The positive sense of the x and y directions are given by the axes in the diagram). O O O O O w = 2 rad/s a = -1 rad/s² 7.93 m/s2 Don't Know -7.93 m/s² 5.93 m/s2 -5.93 m/s² B 60⁰
Show the complete solution that the angle is equal to 72.3°.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The car has a forward acceleration of a = 4.7 m/s2 without slipping its 630-millimeter diameter tires. Determine (a) the velocity (v) of the car when point P at the tire (corresponding to θ = 43° as shown) has zero horizontal component of acceleration. Also, compute for (b) the total acceleration at point P.NOTE: Use purely RMA Method for velocity and acceleration calculations.
Consider the portion of an excavator shown. At the instant under consideration, the hydraulic cylinder is extending at a rate of 7 in./sec, which is decreasing at the rate of 3 in./sec every second. Simultaneously, the cylinder is rotating about a horizontal axis through O at a constant rate of 14 deg/sec. Determine the velocity v and acceleration a of the clevis attachment at B.
The slotted arm AB drives pin "C" through the spiral groove described by the equation r = = (30) ft, where "0" is in radians. If the arm starts from rest when 0 = 60° and is driven at an angular velocity of 8 = (4t) rad/s, where "t" is in seconds, determine the radial and transverse components of velocity and acceleration of the pin "C" when t = 1 s. B C Ans. a₁ = -134.3 ft/s² Ans. ā= 132.6 ft/s²