15. Problem 7: Two solid cylindrical rods support a load of P = 27 kN as shown. Rod 1 has a diameter of 16 mm and the diameter of rod 2 is 12 mm. Determine the axial normal stress in Rod 1 (MPa). 2.5 m 3.2 m (1) 4.0 m (2) 2.3 m B Your answer 16. In Problem Y, determine the axial normal stress in Rod 2 in MPa. Your answer

Q: The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block.…

A: Given data  Diameter of rod AC = 20 mm Distributed load on AB = 4 kN/m Find the axial normal stress…

Q: Axial loads are Bronze Aluminum Steel applied to the compound rod that is composed of an aluminum…

A:

Q: Problem #6: For the beam and loading shown below find the maximum compressive stress anywhere.…

A: Draw the free body diagram of the beam.

Q: The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and allow =…

A: Given A36 steelt=12mmσallow=150MPa

Q: 1. A Rectangular bar as shown in Figure 1 is made of structural steel and subjected to a tension of…

A: It is asked to find the Von-Mises stress and directional displacement of the model given below.…

Q: hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of…

A:

Q: 330k 198k 132k N 16 in.- 12 in. 12 in. E = 29×10086 D = 1.07 in (bigger rod) D=107mind(570.618 in.…

A:

Q: Figure Part A 3 kip μà -1.5 ft d= Value Determine the minimum diameter d of the rod to safely…

A:

Q: A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN. Determine…

A:

Q: 7. A thick-wall cylinder is made of steel (E-200 GPa and v=0.29), has an inside diameter of 20 mm,…

A:

Q: 600 N Problem 5: Fatigue A bicycle crank experiences cyclic loading due to the force applied by the…

A:

Q: Calculate the largest load p on AB in order to keep AC safe:

A: Uniformly distributed load:- Force is evenly distributed over the span of beam It is given that,…

Q: The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, respectively. (Figure 1) Figure…

A: GivendAB=10mmdAC=8mmσallow=150 MPa

Q: The part shown is made from AISI 1040 CD steel and is loaded at point C with 300 N in the positive y…

A: Given : material - AISI 1040 CD diameter of bar d = 12 mmYield strength for AISI 1040 CD is 415 MPa

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 22,kN. Assume that a = 260 mm,…

A: To calculate the average shear stress in the pin at B

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm2, Est…

A:

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

A:

Q: Q2: A composite bar is made up two vertical rods of steel and copper each of length 2 m and diameter…

A: from the above figure given data is load is 15KN in the given question find out each load on the…

Q: Determine the stress in the cable at B, g

A: Need to determine the stress in cable at B.

Q: A stainless steel tube with an outside diameter of 52 mm and a wall thickness of 5 mm is used as a…

A:

Q: 4. Before the 400-kN load is applied, the rigid each of cross-sectional area 1400 mm2, as shown in…

A:

Q: 6. The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the…

A: GIVEN DATA- G=70*10^3 psi Thickness t=1/2in we have to find value of force P

Q: QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "60" N. Calculate…

A:

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A:

Q: b- 10 mm diameter of Brinall hardness ball when the load 500 kgr and HB= 300 determined the diameter…

A: Given: Diameter of the ball=10mmBrinall hardness =300Loading=500kg.f

Q: A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as…

A:

Q: B -1.5 m Figure 2 The -red-brass rod AB of 1.5 m and the aluminium rod BC of 1 m, shown in Figure 1,…

A:

Q: 2 A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN.…

A:

Q: The steel bar has the dimensions shown in Figure 2 below. Determine the maximum axial force P that…

A: To find: The maximum axial force P. Given: The ultimate normal stress is σu=215 MPa. The factor of…

Q: A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa.…

A: Given: d=2.5 m t=25 mm P=1.6 MPa S=250 MPa

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R₁ and R₂ The…

A:

Q: QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "120" N.…

A: Given data: Diameter of rope, d=1 cm= 10mm Tensile load on the rope (along the axis), P=120N.

Q: Question 1. P T The figure (not drawn to scale) shows a cylindrical column submitted to a combined…

A: Consider σx be the normal stress in x-direction and τxy be the torsional shear stress in xy-plane.…

Q: A steel column of hollow circular with length, L is shown in Figure 2. The column cross section has…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.