15. For column AB of W14 x 82, A992 steel, if 4 = 14 ft, L=881 in,1.0. Determine Gp and GromourA) 1.62 and 1.15B) 1.0 and 1.53C) 1.62 and 1.0D) 1.15 and 1.62WIS-50L=358L 800 inL=35L-800 inC4W24-55 BW2455L=358L=358L=1350 in L=1350 in47711177

Answered: Image /qna-images/answer/3313887c-6d7f-4af4-8e83-b0b6f217f897.jpg

Answered: 15. For column = 881 in*, AB of W14 x…

Engineering

Civil Engineering

15. For column = 881 in*, AB of W14 x 82, A992 steel, if 4 = 14 ft, L -1.0. Determine Gp and Gromour

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

600 150 150 Refer to the figure shown. Given are the following: Unit weight of concrete = 24 kN/m fe' = 35 MPa fse = 820 MPa fpu - 1,350 MPa Aps = 1,200 mm? foy = 1.080 MPa Beam is a simple span and have a length = 30 m. Determine the design moment capacity of the section. (kN-m) 00L
6. For the beam and loading shown, calculate (a) the equation of the elastic curve for portion BC of the beam, (b) the deflection at midspan, (c) the slope at B. The beam is W200X46.1 with E-200GPa and load density of 5000N/m with L=6m P L A -LR B W L C X
The square root ratio of the area of the portion of the supporting surface to the area of steel concentrically bearing on concrete support(v(A2/A1) ) is ranging between 25/(A2/A1) < 3 O 1sv(A2/A1) <2 O 4
-15 4.5 2R 影752 DETERMINE THE AREA THG POSITION OF THE CENTROID ABOUT THE REFERENCE AXES AND THE MOMENT OFE NERTIA ABOUT THE CENTROIDAL AXES OF THE COMPOSITE F6URE
5.6 The dimension of a reinforced concrete simply-supported beam supported beam is bxh= 200mm × 500mm, a̟ = 35mm , the concrete is C30, the design value of shear force is V =1.4×10° N, the stirrup is HPB300 grade steel. Please calculate the stirrups required.
A cantilever beam has a length of 2 m and 523 mm depth. Is the beam depth permissible by the code? Type in 1 if yes, otherwise 2. Yes = 1 %3| No = 2
5 Decimal Places..
Pipes in Parallel h₁ = Q₁ = ● ● L₁ f₁, D1 f2, D₂ L2
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
1) Consider the elevation view of an interior beam shown below. The beam has a t-shaped cross- section (the 5 in. thick slab is cast monolithically with the beam - meaning that the 22 in. deep beam has 17 in. hanging below the slab). The c-c length is 30 ft. Assume: M bw = 14 in. fc = 6 ksi Mu,neg. = 340 k.ft en = 28.5 ft Wu h = 22 in. fy = 60 ksi Mu,pos = 230 k.ft Sw = 12 ft - Length hstab = 5 in. No. 4 stirrups Column FL a. Select flexural reinforcement for the beam at midspan assuming it is singly reinforced. T- beams under positive bending are usually singly reinforced because the depth of the neutral axis in the flange is often smaller than the depth of any bars that might be present. Iterate until the design strength, Mn, exceeds M₁ by less than approximately 20%. Provide a drawing of the section design that clearly shows the location of the longitudinal reinforcement. Show the section complies with relevant ACI Building Code requirements (As,min, bar spacing limits, Et, min). b.…
a = 1 m b = 5 m c = 6 m d=1m e = 3 m P₁ = 34 kPa P₂ = 46 kPa P3 = 57 kPa P4 = 26 kPa P5 = 6 kPa (kN \m². (kN m² kN P6 = 117 kPa kN - 1m² kNy \m² kN P₁ P4 a 4. Ry= 5. R= P₂ b P6 KN KN KN B P5 P₂ The L-shaped retaining wall shown retains soil on the right side and water on the left side is to be analyzed. Fluid pressure is shown with bottom pressure equal to P₁ acting on the left side of the wall. Soil pressure is also shown with bottom pressures P2 and P3, acting on the right sides of the wall. Trapezoidal uplift pressure due to seepage is acting at the bottom of the wall with pressure P4 on the side of the water (on point A) and Ps on point B. The horizontal part of the wall is also subjected to the weight of the soil above it with magnitude P6. The wall is made of concrete with unit weight 23.5 kN/m³. Assume 1 meter width for the analysis and include the self-weight of the structure. P3 Calculate the magnitude and location of the resultant of uplift pressure. 1. Magnitude = kN 2.…
Plase answer questions from (d)