15 The figure below represents a time response of a control system. What is it? * Unit-step response of a Prototype First-Order System; Unit-Impulse Response of a Prototype First-Order System; Unit-Step Response of a Prototype Second-Order System: Unit-Impulse Response of a Prototype Second-Order System. opnaduy

15 The figure below represents a time response of a control system. What is it? * Unit-step response of a Prototype First-Order System; Unit-Impulse Response of a Prototype First-Order System; Unit-Step Response of a Prototype Second-Order System: Unit-Impulse Response of a Prototype Second-Order System. opnaduy

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

11. What is not true for the control system stability? d) If a linear, time-invariant system is stable it is zero-input stable and asymptotically stable. e) A system is stable if it returns to the initial equilibrium state when the external action with small duration is removed. f) A linear system is stable if characteristic equation has no root lying in the right-half s-plane. g) A system is stable if its impulse response approaches zero as time approaches infinity.
Problem 1. controller, and G(s) = Consider the control system shown in Fig. 1, where De(s) is the 1 (s - 1)(s+5) 1) (5 points) Is the open-loop system stable? 2) (15 points) Assume that De(s) = K. Rewrite the closed-loop characteristic equation in the root-locus form 1 + KL(s) = 0. Sketch the root locus for L(s). Is it possible to stabilize the system using a proportional controller? == 3) (10 points) Assume that a PD-controller is used to control the system, i.e., De(s) KpKDs. Utilize the Routh-Hurwitz criterion to derive stability conditions for the closed-loop system. + Ro Σ Dc(s) G(s) -OY Figure 1: Control system in Problem 1.
Question: According to Classical Control Theory, The characteristic equation g(s) of a system is given below. The range of K that make the system cross the imaginary axes is: g (s) = s2 + 2s + 3 + K
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
QUESTION 3 An open loop transfer function with a unitary feedback control system is given K by G(s) =- where K is the gain of the system. An open loop (s+1)(s+4) transfer function with a PID controller must be designed in order to yield a peak time of 1.047 s, and a damping ratio of 0.8. 3.1. Calculate the design point s, of the system 3.2. Calculate the gain and the zero(s) of the PID controller 3.3. Provide the block diagram of the compensated system with the PID controller
1 Problem You are given the following data (below) showing the steady-state output response, x(t), of a mass-spring-damper (stable, LTI) system to a sinusoidal input u(t) = A sin(wt). This snapshot is the response after all the transients have decayed (the time is shifted to start at zero for conve- nience). x 0.5225 Displacement pu(t) Sinusoidal force input x 0.1041 1.5 1 Y2 х 0.2783 Y1.372 0.5 h ok -0.5- -1 -1.5 x(t) M Assume: bl u(t) x(t) Horizontal Plane (no gravity) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Time (sec) www k Using only the data provided above (the blue line is the input u(t) and the red line is the output x(t)), determine: 1. The frequency of the input in rad/s 2. The amplitude of the input, A 3. The frequency of the output in rad/s 4. The output-input ratio |G(iw)| = max(x(t)) max(u(t))' at the particular input frequency shown. 5. The phase (also called phase lag) of the output, $, at the particular input frequency shown in degrees. Note the phase is generally…
control of mechanical system give me correct option
Problem 3. Consider the electrical circuit shown in Figure 3 (left). Assume that R₁ = R2 = 1 and C = 1F. 1) (15 points) Derive the transfer function G(s) = Vo(s)/Vs(s) of the electrical circuit. 2) (15 points) If a controller is used to control the system, then the block diagram of the closed-loop system is given by Fig. 3 (right). Suppose that the reference is a ramp signal, i.e., r(t) = t 1(t). Design a controller De(s) such that the closed-loop system achieves perfect tracking (e(t) = r(t) - y(t) → 0). Justify your design. a -> + US R₁i w C: iz iz i3 + R2 Vo RO Σ Do(s) G(s) OY Figure 3: Electrical system in Problem 3.
4
A test was undertaken to find the dynamic properties of a SDOF system. The measured transient response recorded is shown in Figure QA2a. If the stiffness of the system is 1,000 N/m estimate: i) the damping ratio, ii) the undamped natural frequency, and iii) the mass of the system. Displacement (m) 0.08 0.06 0.04 0.02 O -0.02 -0.04 -0.06 -0.08 Figure QA2a 0.5 Time (s) 1.5 2
10- To enter the transfer functions G(s)= a) G= th(2, [3,2]) b) c) d) G(s) TH (2, [2, 3]) G= tf (2, [3,2]) G(s)= TF(2, [2, 3]) 2 3s+2 c) A marginally stable response d) A marginally unstable response to Matlab command use: 3s+1 11- To enter the transfer function g(s)= $2+35+2 ,can be use a) num=[3, 1]; den= [1, 3, 2]; g-tf (den, num) num=[3, 1]; den=[1, 3, 2]; g=tf (num, den) b) c) num=[3; 1]; den=[1, 3, 2]; g=tf (den, num) d) num=(3, 1); den=(1, 3; 2); g-tf (num, den) 12- What is the output of the code (>>p=[0 1]; q=[ 1 -1 0]; step(p,q) ) a) An unstable response b) A stable response (s+1)
Give a physical example for feedback control systems. Sketch the block diagram with input and output variables: Missile launch system