[15 pts] 6) A cylindrical rod having a diameter of 8 mm is to be deformed using a tensile load of 19 kN. It must not experience plastic deformation and a diameter reduction of more than 7.5x10-3 mm. Of the materials listed as follows, which material meets the conditions? Material Modulus of Elasticity (GPa) Yield Strength (MPa) Poisson's Ratio Aluminum alloy 70 200 0.33 Brass alloy 101 300 0.34 Steel alloy 207 400 0.30 Titanium alloy 107 650 0.34

[15 pts] 6) A cylindrical rod having a diameter of 8 mm is to be deformed using a tensile load of 19 kN. It must not experience plastic deformation and a diameter reduction of more than 7.5x10-3 mm. Of the materials listed as follows, which material meets the conditions? Material Modulus of Elasticity (GPa) Yield Strength (MPa) Poisson's Ratio Aluminum alloy 70 200 0.33 Brass alloy 101 300 0.34 Steel alloy 207 400 0.30 Titanium alloy 107 650 0.34

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A prismatic aluminum bar has cross-sectional dimensions 40 x 60 mm and a length of 350 mm. The modulus of elasticity is 70 GPa and Poisson's ratio is u=0.35. When an axial load of 100 kN is applied, the proportional change in the bar's volume is
A copper rod with a diameter of 24 mm is subjected to tension within the elastic region. If themodulus of elasticity is 115 GPa and a Poisson’s ratio of 0.34. Determine the force that willproduce a reduction of 0.003 mm in the diameter.
If Poisson's ratio is 0.42, the Modulus of rigidity is 70.4225 GPa, and the bulk modulus is 416.66 GPa, then the elastic modulus of elasticity is (3 Points) 300 GPa 300 MPa 200 MPa None 200 GPa
A specimen is originally lft long, has a diameter of 0.5in, and is subjected to a force of 5001b. When the force is increased from 5001b to 1,8001b, the specimen elongates 0.009in. Determine the modulus of elasticity (2 decimal places in 103 ksi) for the material if it remains linear elastic.
4.20 A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the magnitude of the load required to produce a 10 in. change in diameter if the deformation is entirely elastic. Assume a Young's modulus of 11 X 106 psi and a Poisson's ratio of 0.33.
A steel rod, 10mm in diameter and 150mm long is subjected to a tensile load of 50,000N. After the test, the length increases to 150.50mm with no appreciable decrease in diameter. Determine the modulus of elasticity of the steel, assuming that the material remains within the linear elastic region.
Please answer d,e,f
Please solve fast!
1. The tensile strength vs. temperature curves of aluminum are plotted below. Explain the meaning of these two curves. 400 Ultimate strength 300 Yield strength 200 100 -200 -150 -100 -50 50 100 150 200 250 Temperature, °C Strength, kPa
The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0 04 0.08 0.12 0.16 0.20 0.24 0.28 0 0005 0.0010.0015 0.002 0.0025 0.0030.0035
If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and length of 10 m is subjected to 2 kN axial tension, compute for its axial deformation
A sample of a steel alloy has a yield strength of 560 MPa, ultimate tensile strength of 630 MPa, and Young's modulus of 200 GPa. a) What is the maximum load that can be applied to a sample with a square cross-section of 10.0 mm by 10.0 mm without plastic deformation occurring? b) If the original sample length prior to testing was 63 mm, what is the maximum length that it can be elongated to without causing plastic deformation? c) What is the difference between elastic strain and total strain?