Answered: 140 lb 12 lb/in. 8 in. Problem 5-54…

140 lb 12 lb/in. 8 in. Problem 5-54 what are the values of the reaction forces O r1=150KNM r2=177KN O r1=177KN, r2=150KN O r1=177.9167N, r2=157.0833KN O r1=171.9KN, r2=150KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.4 For the rigid frames shown in Figure P5-4, determine (1)the nodal displacements and rotation at node 4, (2) the reactions, and (3) the forces in each element. Then check equilibrium at node 4. E, A, and I are identical through all elements. 6m = Figure P5-4 -7.5 m- 6m 80 KN -7.5 m 12 m 9m E = 210 GPa A = 5 x 10-³ m² 1=3 x 104 m²
2 For the spring assemblage shown in Figure 2, determine the displacement at node 2 and the forces in each spring element. Also determine the force F3. Given: Node 3 displaces an amount 8 = 1 in. in the positive x direction because of the force F3 and k₁ = k₂= 500 lb/in. füüvår اشته Figure - 2 3 F3 X
The figure shows a person wearing weight boots and doing lower leg flexion/extension exercise in a sitting position to strengthen the quadriceps muscles and a simple mechanical model of his leg. W1 is the weight of the lower leg, W0 is the weight of the boot, the magnitude of the pulling force applied to the tibia by the quadriceps muscles through the FM patellar tendon, the magnitude of the reaction force acting on the FJ tibiofemoral joint. Point O is the center of the tibiofemoral joint, point A is the point where the patellar tendon attaches to the tibia, point B is the center of gravity of the lower leg, point C is the center of gravity of the weight boot. The distances between point O and points A, B and C were measured as a=13 cm, b=27 cm and c=36 cm, respectively. The angle that the long axis of the tibia makes with the horizontal is β=34°, the angle between the line of action of the quadriceps muscle strength and the long axis of the tibia is α=18°. Points O, A, B and C lie…
Considering small rotations for the following system, determine the 4 by 4 structure stiffness matrix. Hint: Vertical motion and out-of-plane motion are not allowed. The spring is linear. Rigid weightless bar 01,M₁ 02, M₂ u₁,F1 DOFs for rigid bars: 1,1₂,0₁,0₂ U2, F2
The figure shows a person wearing weight boots and doing lower leg flexion/extension exercise in a sitting position to strengthen the quadriceps muscles and a simple mechanical model of his leg. W1 is the weight of the lower leg, W0 is the weight of the boot, the magnitude of the pulling force applied to the tibia by the quadriceps muscles through the FM patellar tendon, the magnitude of the reaction force acting on the FJ tibiofemoral joint. Point O is the center of the tibiofemoral joint, point A is the point where the patellar tendon attaches to the tibia, point B is the center of gravity of the lower leg, point C is the center of gravity of the weight boot. The distances between point O and points A, B and C were measured as a=12 cm, b=24 cm and c=36 cm, respectively. The angle that the long axis of the tibia makes with the horizontal is β=39°, the angle between the line of action of the quadriceps muscle strength and the long axis of the tibia is α=16°. Points O, A, B and C lie…
Problem. Consider the following problem. Find the displacement of node 4. Assume F2=200 N, F3=300 N, F4=400 N and Kı= 100, K2= 200, and K3= 300 N/mm. F. 3 2 3 4 Note: The stiffness matrix of individual springs should be first written, then the equilibrium equations at each node should be written, expanded in terms of nodal displacement, and used to perform the assembly of the global stiffness matrix of the problem. Then, the appropriate boundary conditions should be applied and the nodal displacement vector should be found. Every step should be shown; missing any step would result in point deduction even if the final answer is correct.
Determine the displacement components at node 3 and the element forces for the plane truss shown in Figure P3-27. Let A =3 in and E =30 106 psi for all elements. Verify force equilibrium at node 3. 20 ft 3 5 kip Figure P3-27 10 kip 40 ft 30 ft 30 ft -
Calculate the reaction forces on the bearing near the pulley and bearing at the far end of the shaft. Include a free body diagram and coordinates. Given the shaft length is 1 meter= Mass=40Kg Static load = 8600N Dynamic (running load) = 8400N Some hints:1. This solution will require you to draw known forces and find unknown reactions in 2perpendicular planes and then add the horizontal and vertical reaction forces asvectors to find the reaction force (hypotenuse).2. Bearings are usually mounted as near as possible to the ends of the shaft withoutfouling the other machine elements. The bearing at the far shaft end can be mountedat the 1 meter point. The bearing at the pulley end should allow clearance to assemblethe pulley.3. Bearing reaction forces are typically simplified as a single point load through thebearing centre.
Problem 5 For the following figure, ● Find the reactions expressed as x and y force components Find the reactions expressed as a vector with magnitude and direction ● F = 650 N 100 45° F₂ = 750 N F = 900 N
Find all the non-zero components of internal reaction forces in section a-a. If you select wrong answers, you will have negative score in this question. 200 mm 200mm D 400 N 800 N
The simply supported beam is subjected to the loads as described in the figure and parameter table. Neglecting the thickness of the beam, calculate the horizontal and vertical support reactions at A and B. F A B C -4*- L3 parameter value units L1 L2 L3 ft 4 ft 6 ft theta 65 F 200 lb M 500 lb-ft For the answers, take to the right and up to be the positive directions. The support reaction at A in the z direction is NAz- lb The support reaction at A in the y direction is NAy- lb The support reaction at Bin the z direction is NB= lb The support reaction at Bin the y direction is NBy= lb
Find the rod forces 1, 2 and 3 of the plane truss system shown in the figure. 4m 3m 60kN 40kN 60kN 3m 3m 3m