14. Volume charge density within the operating region of a parallel-plate vacuum diode is given by p.-kood 4/3x-2/3, where the cathode is located at x-0 and the anode at x=d. The voltage between anode and cathode is Vo. If the total charge in a 1-m² cross section is -20 nC and: (a) d - 8 mm, find Vo: (b) Vo-24 V, find d. (c) If d=8 mm and V-24 V, sketch p, vs. x.

14. Volume charge density within the operating region of a parallel-plate vacuum diode is given by p.-kood 4/3x-2/3, where the cathode is located at x-0 and the anode at x=d. The voltage between anode and cathode is Vo. If the total charge in a 1-m² cross section is -20 nC and: (a) d - 8 mm, find Vo: (b) Vo-24 V, find d. (c) If d=8 mm and V-24 V, sketch p, vs. x.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

We know that the Si-diode will pass the current in a forward biased region. This behavior is useful for many applications. C)Plot the V-I Characteristic Curve of the diode.
uO 9:.0 A docs.google.com * ZAIN IQ l. Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 9kQ 1N1199C R2 D1 18KQ 1N1199C D3 1N1199C V2 =12 V R3 1kQ R4 5kQ 1.22 V 11 mA 0.5 A O VD1 ID1 VD2 ID2 صفحة 4 من 6
Consider the diode circuit below, with both diodes having 0.7 V across them when they conduct. V(1) = 10sinwt V (AC)V(2) = 4 V (DC)R(1) = R (2) = 1.3 k(ohm) Over a full cycle of the AC input: 1. Calculate the maximum current through diode 1 (D1). Explain and show all steps. 2. Find the voltage across each resistor. Explain and show all steps. 3. Sketch the current waveform across diode 2 (D2). Label all important points. Explain and show all steps.
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
We know that the Si-diode will pass the current in a forward biased region. This behavior is useful for many applications. Using Multisim build a circuit to observe the relation between the current and the voltage in Si-diode. (Use Diode 1N007GP, 5Ω resistor).
Determine the voltage across the diode in the figure below, using the complete diode model with: r'd = 10-? and r'R = 100-M? a. The value of the forward current. (in Amperes) b. The value of the forward voltage. c. The value of the voltage across the diode.
A pn diode is a semiconductor device in which, unlike in a metal, the current flow is due not only to negative electron charge flow but also due to positive charges. The positive charges are usually referred to as holes, as they are really "deficit" in the negative charge distribution. The semiconduction material (usually silicon with Er = 11 or gallium arsenide with e, impurities are added. Initially, the physically important region on the p side contains a density p+ of positive charges per unit volume, whereas the n region contains a negative charge density p-. When they are brought in contact, a static equilibrium follows in which a surplus of negative charges will accumulate in the (thin) p region, and a surplus of positive charges will accumulate in the (much thicker) n region. These two layers produce an electric field similar to that of a capacitor with infinite parallel plates. In equilibrium, the total number of positive charges in the n region is equal to the number of…
Course: Numerical Analysis
I need an elaboration of this please... Thank youu.
A silicon diode has a forward voltage drop of 1.2V for a forward DC current of 100mA. It has a reverse current of 1μA for a reverse voltage of 10V. Calculate the: a. Bulk resistance b. Reverse resistance c. AC resistance at forward DC current of 2.5mA
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
Question 1: In the circuit shown below, the output (Vo = 10V Max.) Unipolar. The frequency of Primary is 60 Hz. The diodes are Silicon with VD = 0.7V. a. Sketch the output without a Capacitor. b. Determine Voc without a Capacitor. c. Sketch Vs (at the Secondary). d. Determine Voc with a Capacitor of 10 uF across RL. e. Determine the RMS Value of Vp (at the Primary). f. PIV (Peak Inverse Voltage). 10:1 Output C. 22 k1 All diodes are IN4001. | 00000