14-67. The thin-walled pipe has an inner diameter of 12 mmand a thickness of 0.6 mm. If it is subjected to an internalpressure of 35 MPa and the axial tension and tonsionalloadings shown, determine the principal stress at a point onthe surface of the pipe.1000 N+1000 N30 N-m30 N-m

Given thin walled pipeinner diameter di=12 mmthickness t=0.6 mminternal pressure P=3.5mpaouter dia…

Answered: 14-67. The thin-walled pipe has an…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part 2,3,4
5. The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 10 000 psi for the bronze segment AB and 14 000 psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 16 kip - ft is applied as shown. The shear moduli are 6 x 10° psi for bronze and 12 x 10° psi for steel. Bronze Steel A 6 ft
A 180-mm length of 30 x 40 mm solid rectangular bar is loaded as shown in the diagram. The right end of the tube is fixed to a rigid frame while the left end is free. (a) Draw the stress element for point B at the top center of the bar (right end) and label the stress vectors acting on the element, including the stress magnitudes. (b) Draw the stress element for point C at the middle of the front face of the bar (right end) and label the stress vectors acting on the element, including stress magnitudes
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
Two horizontal 22 kN forces are applied to pin B of the assembly shown. Knowing that a pin of 20 mm diameter is used at each connection, determine the maximum value of the average normal stress (a) in link AB, (b) in link BC. 12 mm 45 mm 22 kN 22 kN (Note that maximum normal stress in link AB and BC are required.) 12 mm 60 45 mm 45 C
Determine the shear stress in pin A (double shear) and the normal stress in DE. The diameter of pin A is 0.125" and the cross section of DE is 0.15"x0.25". -2 ft -2 ft C A E 3 ft 600 lb

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

14-67. The thin-walled pipe has an inner diameter of 12 mm and a thickness of 0.6 mm. If it is subjected to an internal pressure of 35 MPa and the axial tension and tonsional loadings shown, determine the principal stress at a point on the surface of the pipe. 1000 N+ 1000 N 30 N-m 30 N-m