14-41. The pipe system consists of a 3-in.-diameter, 100-ft- long galvanized iron pipe, a fully opened gate valve, four elbows, a flush entrance, and a pump with the pump head curve shown. If the friction factor is f= 0.022, estimate the flow and corresponding pump head generated by the pump. 18 ft hung (t) 160 140 120 100 80 60 40 20 Q gal/min 50 100 150 200250300350400450 S00

14-41. The pipe system consists of a 3-in.-diameter, 100-ft- long galvanized iron pipe, a fully opened gate valve, four elbows, a flush entrance, and a pump with the pump head curve shown. If the friction factor is f= 0.022, estimate the flow and corresponding pump head generated by the pump. 18 ft hung (t) 160 140 120 100 80 60 40 20 Q gal/min 50 100 150 200250300350400450 S00

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Installed is a venturi meter on a pipe 30 cm diameter in which the maximum flow is 2.7 cum of water in one minute. The throat is 15 cm in diameter. Compute the theoretical discharge that would be passing through the meter when the differetial manometer is as shown. Calculate also the discharge coefficient, C.
A flocculator is 16 ft (4.88 m) deep, 40 ft (12.2 m) wide, and 80 ft (24.4 m) long. The flow of the water plant is 13 mgd (20 cfs, 0.566 m³/s). Rotating paddles are supported parallel to four horizontal shafts. The rotating speed is 2 rpm. The centre line of the paddles is 5.5 ft (1.68 m) from the shaft (mid-depth of the basin). Each shaft equipped with six paddles. Each paddle blade is 10 in (25 cm) wide and 38 ft (11.6m) long. Assume the mean velocity of the water is 28 percent of the velocity of the paddles and their drag coefficient is 1.9. Estimate: (a) the difference in velocity between the paddles and water (b) the useful power input (c) the energy consumption per million gallons (Mgal) (d) the detention time (e) the value of G and Gr at 60 °F (f) the loading rate of the flocculator
????
In differential equation Find the time to drain the tank completely (a) when c = 1.0 (b) when c = 0.65. If a horizontal cylindrical tank is 10 ft long and 2 ft in radius. A pipe with a nominal size of 1/2 inch schedule 10 is used as the outletix. The tank is initially 75% full of water.
Determine the shaft horsepower for an 80% efficient pump to discharge 30L/s through the system. The system losses, exclusive of pump losses, are 12V2/2g and H = 16m. Ans: 8.75hp H 150mm dia
A submersible deep well pump delivers 800gal/h of water at 60°F through a 1in SH. 40 SP, when operating in the system shown below. If the total length of pipe is 150ft, calculate the power delivered by the pump to the water. Consider friction loss, but neglect the other minor losses.
The table below gives the pump curve data for a pump operating at 1000 rpm and has 3-in. impeller. The available pumps had different impeller diameter D and rotation speed N as shown below. 1. Draw the pump curve for each pump. 2. What is the discharge provided by each pump when the Head is equal to X? Standard Pump Flow (gpm) Head (ft) 80 500 75 Pump 1 Pump 2 Pump 3 1000 73 N (rpm) D (in) 750 500 600 1500 70 4 6. 2000 67 2500 62 3000 58 3500 52
Give me all answers otherwise leave it. I I don't want partial answers. I remember please give me a, B, c, d and e... Please thank you
For the setup shown in the figure :
Explain with diagram plzzz
Water is pumped from reservoir A at elevation 250 m. The pump is close to reservoir A and is at the same elevation as reservoir A. It is pumping 90 liters per second of water through a 1,000 m of 150 mm diameter pipe to a reservoir whose elevation is 300 m. What is the horsepower delivered by the pump? Assume f=0.02 and neglect minor losses. Select one: O a. 150.50 Hp O b. 302.23 Hp O c. 267.72 Hp O d. 252.30 Hp
q7