5-7E A garden hose attached with a nozzle is used to fill a 20-gal bucket. The inner diameter of the hose is 1 in and it reduces to 0.5 in at the nozzle exit. If the average veloc- ity in the hose is 8 ft/s, determine (a) the volume and mass flow rates of water through the hose, (b) how long it will take to fill the bucket with water, and (c) the average velocity of water at the nozzle exit.

5-7E A garden hose attached with a nozzle is used to fill a 20-gal bucket. The inner diameter of the hose is 1 in and it reduces to 0.5 in at the nozzle exit. If the average veloc- ity in the hose is 8 ft/s, determine (a) the volume and mass flow rates of water through the hose, (b) how long it will take to fill the bucket with water, and (c) the average velocity of water at the nozzle exit.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 150-m-long commercial steel pipe is to convey 30 L/s of oil (s = 0.9, p = 0.038 N-s/m?) from one…

A: Introduction : Minimum costs for medium transmission through the pipeline, as well as pipe costs,…

Q: Gasoline at 20°C is pumped through a smooth pipe at a steady flow and the pipe diameter is constant.…

A: In this water is flowing from lower elevation to higher elevation..As there is diameter of pipe is…

Q: NOTE (h in ft) h = 8.881 ft Problem II. A proposed elevated tank for a certain community has a…

A: Given Unit weight of water= 62.4 lb/ft3 Height of tank = 120 inches

Q: A centrifugal pump delivers water at the rate of 50 kg/s. The inlet and outlet pressures are 2 bar…

A: A Centrifugal pump is a machine that converts rotational kinetic energy into hydrodynamic energy.

Q: a venturi meter having a diameter of 6 in, at the throat is installed in a horizontal 18-in. water…

A: Here Sm = manometric fluid Sf = flowing fluid a) Discharge when friction is neglected,…

Q: Gasoline (v = 4.06 E-7 m²/s) flows at 0.9 L/s through a 100-mm-diameter pipe. Describe the type of…

A: Given Kinematic viscosity = 4.06*10-7 m2/sec Dia of pipe = 100mm = 0.1 m Discharge= 0.9 lit/sec…

Q: A pump is to deliver 80 GPM of water at a density of 61. 83lb/ft cubed with a discharge pressure of…

A: Given Discharge Q=80 GPM=80×0.000063 m3/sec=0.00504 m3/swater unit wt γ=61.83 lb/ft3=9.71…

Q: Water discharges through an orifice on the side of a large tank. The orifice is circular in cross…

Q: SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in…

Q: 75 mm diameter nozzle is shooting out water from the pipe. Assume negligible head loss, determine…

A: Given data, h1=1.8 m D=150 mm p=100kPa Diameter of nozzle = 75 mm To find out the velocity at A,…

Q: A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a…

Q: A venturi meter with 150 mm diameter at inlet and 100 mm at throat is laid with its axis horizontal…

Q: c) For the system shown in Figure 3.1, calculate (i) the volume flow rate of water from the nozzle…

A: To find (a)Q=? (b)Pa=?

Q: A pipe 2000 m in length with a flow rate of 2 m /s. At the end of the 600 mm pipe, a valve is…

A: To determine the pressure due to closure of valve. Given, Length of the pipe (L) = 2000 m Flow…

Q: Figure Q1 (a) shows the tank attached with piezometer tubes. The pressure gauge A is 2.3 kPa. The…

Q: A centrifugal pump is being designed to pump liquid refrigerant R-134a at room temperature and…

Q: A pipeline with a pump carrying a 50 L/s discharge leads to a nozzle as shown. If the 180 mm…

Q: The 250-ft-long hose is made of a material having a roughness of = 0.0005 ft. (Figure 1) Figure 80…

Q: 6:687 Oil (sg = 0.85) h cm 35-mm diameter 100-mm inside diameter Flow B- A+ 1.0 m

Q: Determine the minimum flow capacity Qfilter, in units of liter per minute (Ipm), of the return line…

Q: 0-cm fire hose with a 3-cm nozzle discharges 1.5 m3/min to the atmosphere. Assuming frictionless…

A: D1 = 10 cm D2 = 3 cm Q = 1.5 m3/ min.Patm = P2 = 0 we have to find- The force (FB) exterted by the…

Q: 2. Given the figure below, solve for flow rate in the venturi meter. (C = 0.984) 2 (Ø - 250mm) oil…

Q: Two pipes 1 and 2 are connected in parallel. Pipes 1 and 2 have the same length and diameter. If the…

Q: A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter…

Q: Q2- Water ( p= 990 kg/m' & u= 0.001 pa.s) is pumping from a water tank to water injection well with…

A: Re=ρvdμ Where, ρ=Density of water= 990kg/m3 v= velocity=…

Q: Two pipes 1 and 2 are connected in parallel. Pipes 1 and 2 have the same length and diameter. If the…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

5-7E A garden hose attached with a nozzle is used to fill
a 20-gal bucket. The inner diameter of the hose is 1 in and
it reduces to 0.5 in at the nozzle exit. If the average veloc-
ity in the hose is 8 ft/s, determine (a) the volume and mass
flow rates of water through the hose, (b) how long it will take
to fill the bucket with water, and (c) the average velocity of
water at the nozzle exit.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Step 1

Step 2: Step 2

Step 3: Step 3

Step 4: step 4

Solution

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2- Water ( p= 990 kg/m' & µ= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.
I need the answer as soon as possible
This
NOTE (h in ft) h = 8.881 ft Problem II. A proposcd elevated tank for a certain community has a diameter of 72 inches and a height of 120 inches. It is to draw water by a pump from an aquifer down below the ground. Two steel hoops, 24.4 in? in cross section, are installed around the tank, one at the bottom and one at the top, to prevent the bursting of the tank by the water pressure inside. (Use unit weight of water, yoater = 62.4 lb/f³) a) Compute the internal stress at the bottom of the tank (in psf). b) Determine the tensile stress at the top (in psi). c) Determine the tensile stress at the bottom (in psi).
A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. (A 19.28 L/s B No Answer among the choices 24.31 L/s D 29.05 L/s (E 32,56 L/s
An empty water tank has a diameter, D=6ft, and height, H=10ft, an inlet valve witha diameter, din =6”, and an outlet valve with a diameter, dout =4”. a) Estimate the time in minutes requiredto fill the tank if the outlet valve is closed and inlet velocity is constant at measured at 0.1ft/s.
A pump is used to draw water from an open reservoir to an open tank on thetop of a building. The discharge flow rate is 50 lps. The static suction head of the pump is6 m and the static discharge head is 20 m. The cast iron, schedule 40, pipe in the suctionline is 4 inches nominal diameter and 20 m long. The cast iron, schedule 40, pipe in thedischarge line is 6 inches nominal diameter and 65 m long. The fittings and valvesinstalled in the suction line are the following: two 90o standard elbow and one gate valve.For the discharge line, are the following: one check valve, one gate valve, and three 90ostandard elbows. Assuming a water viscosity of 0.001002 Pa-s, and a pump efficiency of82 %. Determine: a) the total dynamic head b) the pump brake power. Show the neat schematic diagram of pumping system. Note: Use Moody’s equation for the value of friction factor; and table for determining the equivalent length of the components.
URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by step solution. Box the final answers. Do not shortcut your solution. I will give an upvote if it satisfies. Thank you! When the flow of water through a horizontal 300 mm x 150 mm Venturi meter (C=0.95) is 0.111 cu.m/s. a. Compute the theoretical discharge. b. Determine the velocity at the throat. c. Find the deflection of the mercury in the defferential gage attached to the meter.
100mmgl 个一 680mm 320 mm I320m 300mm A H2O A vertical venturi meter 100mm diameter is installed in a 300mm diameter vertical pipe as shown. The flow is upward. If the specific gravity of the mercury at the bottom part of the manometer is 13.6, determine the a) Discharge neglecting head loss, b) Discharge if head loss from point 1 to point 2 is 500mm, and c) Coefficient of discharge (This is a multiple answer question. You must have 3 selected choices since there are 3 required answers in the problem) A No answer among the choices in question A B No answer among the choices in question C C = 0.819 D No answer among the choices in question B E) Q = 70.3 L/s Qt = 86.2 L/s G) Qt = 65.8 L/s H) Q = 86.2 L/s Q = 65.8 L/s C = 0.936 к) с30.753 Qt = 70.3 L/s M) C = 0.668 N) Qt = 57.6 L/s o Q = 57.6 L/s
A cylindrical tank with vertical axis contains water. A 50 mm orifice is located at the side 0.60 m above the bottom of the tank and 1.50 m directly above the orifice is another orifice 75mm diameter. Cv is 0.98 and C is 0.61 for both orifices. Determine the: show complete solution thumbs up guaranteeda. h1 in metersb. Discharge in the lower orifice in lit/secc. Total discharge from the 2 orifices in lit/sec
A - is a wrong answer.
FLUID MECHANICS!!! TY!