130 mm 25 mm 25 mm FIG. P1.30, P1.31 1.31 Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?

130 mm 25 mm 25 mm FIG. P1.30, P1.31 1.31 Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The rods AB and BC are connected by pins at A, B and C, as shown in the left side of Fig. 2. The…

Q: solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: Given data as per questionLoad on the bar =25 kg=245.25 NLimiting stress of the bar =27.24kpawe know…

Q: 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in…

Q: 1.5 (A). A simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded…

Q: EXERCISES 4.1 A steel bar of diameter 15 mm is loaded as shown in Fig. 4.28. Calculate the stresses…

Q: 1.39 The bar AB is supported by a frictionless inclined surface at A and a 7/8- in.-diameter pin at…

Q: The figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

A: Given data:τ=70 MPaσb=140MPaABC=864 mm2ABE=1780 mm2for shearing n= 5 rivetsfor bearing n=7 rivets

Q: The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the…

Q: A connecting link, 160mm in length, is 50mm in diameter for a length of 100mm and 30mm in diameter…

Q: Two portions of member AB are glued together along a plane forming an angle with the horizontal. The…

Q: A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under…

A: Calculate the strain in the wire. ε=δll Here, l is the original length of the wire, δl is the change…

Q: Two square bars (15mm thick) are bolted together as shown. Volt's allowable shear stress is 90 MPa,…

Q: QUESTION 2 A connecting link, 160mm in length, is 50mm in diameter for a length of 100mm and 30mm in…

Q: A 16-mm-diameter steel [E= 200 GPa] rod (2) is connected to a 50-mm-wide by 8-mm-thick rectangular…

A: The elongation of member when subjected to a longitudinal force is calculated using the formula…

Q: 1.8 (A). A steel bar ABCD consists of three sections: AB is of 20 mm diameter and 200 mm long, BC is…

A: AB bar diameter =20 mmBC bar diameter=25 mmCD bar diameter=12 mmAs the bar is subjected to…

Q: The lap joint shown is fastened by four 314" dia. bolts. Assume the applied load is uniformly…

Q: tive and compression negative. 45°

A: Draw the free body diagram for the above problem as follows.

Q: Problem 2: At a point in an elastic material, there are two mutually perpendicular planes, one of…

A: The principal plane position θp=21.263° The shear plane position…

Q: Q1. A bracket, as shown in Fig. is supported by 5 bolts, two at the bottom and three above.…

A: To find: The size of bolts. Given: The factor of safety is FOS=2. The number of bolts n=5. The yield…

Q: Q.1. A T-section 150 mm×130 mm×30 mm is used as a strut of 5 m long with hinged at both ends.…

A: First, you need to calculate the effective length of the strut in both boundary conditions (both…

Q: The connection shown consist of five steel plates joined by a steel bolt with a diameter of 6 mm.…

A: The given information in the problem is shown in the following attached image:

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

Q: A bar with a cross-sectional area of 1300 mm, length of 1.5 m, modulus of elasticity of 70 GPa, and…

Q: Hertz contact theory can be used to determine the stresses due to contact between two spheres, which…

A: It is asked to find the stress by using Hertz contact theory

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: Jmm 70.1 Ø20 0,1 Ø10 20 01

A: Let the external force acting on the bar is as shown below, Let the modulus of elasticity of…

Q: ding to R.S. Kh

Q: P1.27 The pulley shown in Figure P1.27 is connected to a bracket with a circular pin of diameter d =…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

P
130 mm
25 mm
25 mm
P
FIG. P1.30, P1.31
1.31 Assume that the axial load P applied to the lap joint is distributed equally
among the three 20-mm-diameter rivets. What is the maximum load P that can be
applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing
between a plate and a rivet, and 120 MPa for tension in the plates?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
1.19 Find the stresses in members AB, BC , and CD for the truss shown. Indicate tension or compression. The cross-sectional area of each member is 1600 mm². В 3 m 3 m 4 m E A C 40 kN 70 kN 4 m F
2.24 A rubber bearing pad under the steel girder above is used to produce a relatively uniform bearing stress on the concrete below. The literature from the pad manufacturer suggests that strain in the particular bearing pad should not exceed 12%. Due to the dead loading of the structure's weight, the pad is already strained by 3%. Say the live loads could produce an additional 0.25 in. of vertical motion of the girder, which must be tolerated. Determine the acceptable range of pad thicknesses that keeps strains below the maximum allowable strain. Prob. 2.24
A cantilever beam, 80 mm wide by 290 mm high and 9 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Determine the magnitude of the stress in a fiber 50 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
A cantilever beam, 80 mm wide by 220 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1500 N/m at the wall. Determine the magnitude of the stress in a fiber 70 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
1.2 A hollow circular short column of outside diameter 300 mm and thickness 10 mm carries a load of 1000 kN. Determine at what eccentricity along a diameter can the load be placed if the permissible stresses are 150 N/mm2 in compression and 80 N/mm2 in tension.
A book is to be mounted on a wall as shown. Weight, W, is 2000N. Shear stress in the bolts should not exceed 60MPa. Determine the minimum standard diameter of the metric bolt/screw that should be used.
2. A compound bar of length 500 mm consists of a strip of aluminium 50 mm wide and 25 mm thick and a strip of steel 65 mm wide x 20 mm thick rigidly joined at the ends. If elastic modulus of aluminium and steel are 1 × 105 N/mm² and 2 × 105 N/mm², calculate the stresses developed in each material and the extension of the compound bar when axial tensile force of 60 kN acts.
QUESTION 2 1.2 A thin cylindrical pressure vessel has the following specifications Internal pressure 5.33 MPa Metal thickness 20 mm Maximum allowable stress 120 MPa Efficiency of the longitudinal joint Efficiency of the circumferential joint 80 % 50 % 1.21 Determine the maximum internal diameter which the cylinder may have. 1.2.2 The actual values of the hoop and longitudinal stresses. For the soolbar, press ALT=P10 (PC) or ALT-FN-F10 (Mac). B IUS Paragraph Ara !! 140x AITZAN LAINA
A 40mm thick steel bar that is fabricated by welding two parts together is shown below. Being concerned for the strength of the weld, you need to find the state of stress (normal stress and shear stress) in the plane of the weld for an applied load of 400kN. Draw your result on a stress element. 57° 400 kN 400 kN 100 mm