13. The front of the platoon (truck) has a speed of 30 mph in question 12. According to the shockwave speed, the platoon is growing at a rate of:

Q: Identify if the truss system is determinate or not and draw a red line on the zero-force members.

A: A.) Determinacy Recall the rules of determinacy and stability for trusses. b+r<2j,…

Q: For the control system Draw Nyquist Plot with Solution G(S)= 63.625 (S+1)(S+3) S(S+2)(5+65+18) (5+5)

A:

Q: Problem #2 (Moment Distribution 11-11 from text) Determine the moments and B, C and D. El is…

A: Step 1: Step 2:Step 3: Step 4:

Q: Design a simply supported one-way pavement slab for a factored applied moment, Mu = 10 ft- kip. Use…

A: For a simply supported one-way slab, the minimum thickness, h, can be estimated using the empirical…

Q: please the correct answer

A:

Q: The L6 x 4 x  1/2  single angle shown has two rows of bolts. Each leg has one row (one line) of 5/8…

A:

Q: 1: Determine the load capacity of the one-way uniformly loaded (5 kN/m²) simply supported slab shown…

A:

Q: 4. Calculate the magnitude and direction of the resultant pressure-force on the gate as shown in…

A: Step 1:

Q: Q9;Find the invert level for each pipe and the manhole type From to Dmm Lm S Invert Invert in out…

A: Step 1: Step 2:Step 3:Manhole  types are determined based on depth Only .The depth is the difference…

Q: In the figure below, assume that complete mixing occurs between the two inflows before the mixture…

A:

Q: The cantilever beam shown below supports a uniform service (unfactored) dead load of 1.5 kip/ft plus…

A:

Q: A lane group at an signalized intersection has three lanes with through traffic movements only .…

A:

Q: AW18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P = 24 kips, w…

A: Final Answerσmax​=41.5 ksi

Q: Determine all reactions for the beam by applying the Moment Distribution Method. Provide detailed…

A:

Q: 7. A rectangular, unfinished concrete channel of 38-ft width is laid on a slope of 8 ft/mi.…

A: Detailed explanation:

Q: The circular slab of radius 2 m supported by three columns, as shown in figure, is to be…

A:

Q: need help

A: Step 1: Given Data: ​Cross-sectional area of the steel bar:A=6 in2Yield strength of steel:Fy​=36…

Q: how many custom bricks of size 3 1/4 x 3 3/4

A:

Q: Determine the collapse load for the simply supported slab. 3 m 3 m

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine the heel and toe stresses and the factor of safeties for sliding and overturning for the…

A:

Q: A composite beam is fabricated by bolting two 3.1-in.-wide by 14-in.-deep timber planks to the sides…

A:

Q: Consider the space truss represented schematically in Figure 1. It has 21 struts and a fixed support…

A:

Q: Time: 1. Hrs During the last ten days: In one of the productive operations, the electronic control…

A: More explain

Q: Two group of students are collecting traffic data at the two sections A and B 200 meters apartalong…

A: We compute the Time Mean Speed (TMS) and Space Mean Speed (SMS) by using the following formulas:…

Q: A simple circular curve exists with a radius of 900 ft connects the tangents of a two-lanehighway…

A:

Q: Calculate the bending stresses using the section shown before your name;

A:

Q: Please explain step by step and show formula

A: Step 1: We are given two traffic flow conditions on a single-lane roadway without overtaking: (i).…

Q: Aggregates from three sources having the properties shown in Table P5.41were blended at a ratio of…

A:

Q: 4.36 A pipe slopes upward in the direction of liquid flow at an angle of 30° with the horizontal.…

A: Detailed Solution for Problem 4.36

Q: NEED HELP

A:

Q: A cylinder of fluid has dimensions of 0.2 ft in diameter by 0.45 ft high. If the weight of thefluid…

A: The volume of a cylinder is given by the formula V = πr2h, where r is the radius and h is the…

Q: Given a portion of a pipe network below. Determine the true discharge in each pipe using the…

A:

Q: Given the following end areas for cut & fill, complete the eart calculation using a shrinkage of…

A:

Q: 3. As the audio frequency of Fig. 11-7 goes down, what components of Fig. 12-4 must be modified for…

A:

Q: My desk has a weight of 193.044 lbf on the Earch's surface where the acceleration of gravity is…

A:

Q: -T -3T +5T *A 1 m Bx Fig. 1: Shaft with torques

A:

Q: If a contractor has to quit a project due to a lack of funds what would be the best way to handle…

A: Approach to solving the question: The approach to writing the answer above is structured and…

Q: Determine the heel and toe stresses and the factor of safeties for sliding and overturning for the…

A:

Q: / An irrigation project requires digging and paving an irrigation canal with alength of (30 km) and…

A:

Q: Please answer the following and show me the step by step so

A: Step 1:Step 2:

Q: An engineer is designing a fountain, as shown, and will install a nozzle that can produce a vertical…

A: :

Q: For the beam show below, draw A.F.D, S.F.D, B.M.D A 2 N M 10 kN.m B 2 M C

A: Step 1:Step 2:

Q: An urban county with an area of 1,000 mile2 has an estimated 18 million miles of vehicular traffic…

A: To determine the total VOC emissions from all sources in tons per day, we will calculate emissions…

Q: a. Determine the net area of the W12x16(Ag=4.71in2) shown in Fig. Assuming that the holes are for…

A: Detailed explanation:

Q: please help

A: The total load on the beam is the sum of the dead load (D) and the live load (L). The dead load is…

Q: 12.36 Figure P12.36 shows a 3 × 5 pile group consisting of 15 concrete piles of 400 mm diameter and…

A:

Q: What is the formula of B coefficient  beta T and beta C if you will not use any software ?

A: Assumptions:   - Multicollinearity between T and C is negligible. If not, you would need more…

Q: The difference in water surface levels in two tanks, which are connected by three pipes in series of…

A: 1. Problem SetupTanks: Two tanks with a water level difference of 12 meters.Pipes: Three pipes in…

Q: m A square slab is simply supported along all sides and is to be isotropically reinforced. Determine…

A:

Q: 10:46 Mechanics of Deform... ← CE104.2T.24.25. FA 1 5 of 6 2.5/10 Rigid bar ABCD is loaded and…

A: