13 in. 11 in. 7 in. 140 D 4 in. ES

Q: 20. = 3,500 mm, w = 0.5 m A = 2 cm²

A:

Q: Q1/ A:1. For the triangle shown in the (fig.1) below; Determine the length of (AC); (L)

A: Given data: Length of perpendicular side BC, P = 15 cm. Length of base side AB, B = 20 cm. Part…

Q: How we find the Metacentric Height using Metacentric Height Apparatus?

A:

Q: (b) thickness of 15 mm as shown in Figure Q4. The pressure inside the tank is maintained at 10 MPa.…

A:

Q: Block A has a mass of ma = 59.0 kg and rests on a flat surface. (Figure 3)The coefficient of static…

A:

Q: Resolve and draw the diagram of all internal efforts

A: For the above diagram, We draw a free body diagram,

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: .Find (ly) for the shaded area Y 2m 2 6m 1 3 оз 3m 3m 3m

A: Mass moment of inertia measures a body resistance towards rotational motion. If a body have more…

Q: A) Draw a Free Body Diagram of the ABC bar. B) Draw a Free Body Diagram of the CDE piece. C)…

A: According to the details provided in the question, we need to find  F.B.D. of the ABC and CDE part…

Q: The distance y from the back of the shorter leg to the neutral axis XX is

A:

Q: 0.4 m 0.4 m 45 Va

A:

Q: determine: Magnitude of Dot Product in lb (express in 4 significant figures). x- component of rAB in…

A: Given: The force along AB, FAB = 780 N

Q: Determine the acceleration of the slider block C at this instant?

A: Given: To determine: Sliding velocity of Slider C

Q: ompute the moment of inertia, Ix of the crosS-sectional area about the neutral axis. + 6 in.- 6 in.…

A:

Q: Q.1) Determine Ixx, lyy and Ixy for the section shown below. y y = x 1/2. 0.6 m y = 0.36 m

A:

Q: What are the forces cx and cy? Force F = 150

A: Given data F=150lb

Q: 2. A rectangular piece of metal has a hole cut in its center (1cm high by 4cm wide) as shown in the…

A: Explanation: As metal is heated from 0°C to 150°C, there will be thermal expansion.  Rise in…

Q: When installing an air conditioner in a car, hose with a diameter of 2.5centimeters is used. Each…

A: Air conditioner is a device used to produce cooling by dissipating heat in the form of fluid or…

Q: Does this machine maximize or minimize the force (100 Ib) *

A: Reaction force acting on the point B is RB×1.5=100×20RB=1333.33 lb As the reaction force acting at…

Q: 15 What is the weight of the weldment shown? (MS) Plate= .2835 lbs. per cubic inch. V 58" x 21 x 21"…

A:

Q: Determine radius of mohr circle

A:

Q: مسكن You can see a pipe assembly. pipe assembly, which is fixeed to a well at point A and loaded at…

A:

Q: A B Cell 1 Cell 2 с D Figure 1. A double-cell thin-walled section of a fuselage. Table 1. Geometric…

A:

Q: Q2 A small marble at point A of mass 0.5 kg as shown in Figure Q2 is release downward with an…

A: Given data: VA = 2 m/smass of body = 0.5 kgtan θ = 34 θ = tan-1(34) = 36.87°

Q: Determine the radius of mohr circle

A: Given data : σX=25 MPaσY=-48 MPaζXY=-18 MPa

Q: A particle travels along the curve from A to B in 6 s. It takes 8 s for it to go from B to C and…

A:

Q: 1.25 m y 180 N '0.5 m F2 0.75 m

A: In the scalar method, the moment can be calculated as follows: In the cross-product approach, the…

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: The loss coefficients for the pipe shown is: up to A it is 0.6, from A to B it is 1 from B to C it…

A:

Q: Find the force of the rods AB, AC, BC, CD and AD. 20 N 40 N B 10 cm A D 10 cm

A:

Q: Assignment Find the centre of area (centroid) of the following figures. 4 in.- 5 in. in. 2 in. -1…

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: For the link BCE, a) Write the singularity function fo b) Sketch the V diagram

A: given

Q: ajor principal axis of the section with respect to

A: major principal axis can be obtained as below,

Q: QUESTION 2 A man is throwing a basketball as shown in Figure Q2. Determine: a) the speed at A, vĄ so…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.