13-14 Rods AC and BC are used to su which the average normal stress can not exceed 150 Mpa What is the force on one tension rod given the assembly is symmetrical? (1kg = 9.81N) C.2.26 kN CS CA 15ed with B.r.se *** 3.1.5€. Sean C-?2 D. 3.92 KN Determine the minimum requirea diameter of each rod. A. 5.77 mm B. 4.38 mm C. 4.08 mm D. 3.10 mm 60 c

Q: Two square rods AB and BC are welded together at B and loaded as shown. Determine the average normal…

A:

Q: A machine member is subjected to forces as shown in Fig. B 300- 3 kN-m 1.5 kN-m 20 kN Determine the…

A: A )  To find : Determine the stresses ? A problem of solid mechanics.

Q: A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN…

A: Given:- The magnitude of the force (P) = 4.5 kN The dimension variable (b) = 240 mm = 0.24 m The…

Q: Solve the plate shown in the figure, Include fbd on solutions

A:

Q: the loading shown, determine (a) the stress at points A and B, the point where the neutral axis…

A: A=4*1.8=7.2 in3 Iz=(4*1.83)/12=1.944 in4 Iy=(1.8*43)/12=9.6 in4

Q: hown in the figure. The properties of the segments and the work ble. Determine the maximum allowable…

A: Solution: For  compound bar (Steel section) Ast=0.75in2Est=30×106 psiLst=2×12=24…

Q: 1. The compound shaft supports. For the bronze segment AB, the maximum shearing stress is limited to…

A:

Q: Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum…

A:

Q: For the lap joint below, the maximum safe load P if the shearing stress in the rivets, (diameter of…

A: This question is related to the Bolt connection from Steel design

Q: The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear…

A: Given data in question Load 750 kN Diameter 32 mm To find out  Permenant strain

Q: J- A T beam supports the three concentrated loads shawn. Öctermine the merximum tensile 1.41 KN 5.64…

A:

Q: The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm. square cross-…

A:

Q: Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

A: From the arrangement, we can observe that the maximum tensile strength occurs in the line of rivets.

Q: . For the riveted connection shown in the figure using  elastic analysis a. Determine the safe value…

A: Diameter of rivet = 25 mmAllowable shear stress = 150 MPaloading = 50 KNOther Data are given in the…

Q: A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of…

A:

Q: P P 130 mm 25 mm 25 mm 3. Assume that the axial load P applied to the lap joint is distributed…

A:

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A:

Q: - shress in each raod.

A:

Q: Calculate the shear stress in MPa at section B A 100 mm F=10EN 10 mm

A: Shear stress:- shear stress is defined as shear force per unit area.

Q: Problem 1: Method of Joints Inputs: a = 7 m F₁ = 15 KN ● F₂ = 10 KN ● ● There is a pin at A and a…

A: GivenTo findForce in each member of truss

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.