12. A tank compose of hemispherical at the bottom and frustum at the top as shown in figure. A sharp edged orifice located at the bottom with a diameter of 100 mm and C= 0.60. Determine the following A) The time to empty the frustum B) Time to empty the tank 12A t = 1236.79ss 12B t=2031.43ss 5 m 2 m 3 m

12. A tank compose of hemispherical at the bottom and frustum at the top as shown in figure. A sharp edged orifice located at the bottom with a diameter of 100 mm and C= 0.60. Determine the following A) The time to empty the frustum B) Time to empty the tank 12A t = 1236.79ss 12B t=2031.43ss 5 m 2 m 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through a horizontal pipe of cross sectional of 20 cm2. Atone section, the cross sectional area is 4 cm2. the pressure difference is29.4 psi. How many cubic meters of water will flow out of the pipe in 1min? (can you show the diagram or illustration if possible. thank you!) Choices: a. 0.008 b. 1.208 c. 0.493 d. 0.0185
d A) Determine the total force on the cylindrical gate. d = 9 ft, a = 3 ft, and the gate is 4 feet wide. The specific weight of water is 62.4 lb/ft^3.
Given: A pipe connecting two reservoirs as shown in Fig. 1. Absolute roughness of both pipe sections is 0.5 mm. Calculate: a) Equivalent pipe loss coifficient b) Equivalent pipe length which can replace the secondary losses c) Discharge in the two pipes (ignore secondary losses) d) Equivalent pipe diameter required to replace the two pipes in series (Leq = 2500m) e) Sketch EGL ( solid line) and HGL (dash line) H= 50 m L = 1000 m 2000 m- %3D Water 20°C 70 m-t D= 200 mm Valve D =300 mm Figure 1 (Half closed)
M-(1zy.z-ly.y)+ M,(1;.z – lzy.y) Iz.ly - Izy Pr My Formüller; a =- • 01 • Ox 2 Pr Ox + dy o - o0, + o3 < ož , Jort = • 02 = 2t Tmaks 2 2 w Oz + Oy Tc d'y M(x) + Ty , 8 = aAT, T=. I dx2 - a. Omaks.min %3D EI MalanıcoXc, @pc El Malanipc EI A (0x Tmaks + Tây tc/p = 2 В n'El ap ax. Per = vQ It y EI L- Calculate the reaction at support A for the beam and loading shown in the figure. w = 5 N/mm and L = 1.2m 2250 N 3520 N 1930 N 2680 N 3210 N
What would be the rotation rate (in rad/sec) if during rotation the water in the right leg (with a diameter of d) decreases a distance h1=0.03 m? A U-tube, Elevation = 20 cm d - 20 сm 2d → Elevation = 0 -20 cm- B 20 cr A
Please help me with this problem clearly. List two sources of error in the water-filled tube and pressure gauge method of measuring head for a hydro system and how to avoid them. Using this method, a series of measurements up a hill to the source of the stream produces the following heights: 1.5m, 0.7m, 1.0m, 1.9m, 1.6m, 0.3m, and 0.8m. What is the total head for this site? If the flow rate was 0.5 m3s-1, calculate the power available in this stream?
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. Choices are listed below and draw its FBD. A.-4.67 m B.-2.72 m C.12.74 m D.2.56
K A rain gutter is to be made of aluminum sheets that are 16 inches wide by turning up the edges 90°. See the illustration. (a) What depth will provide maximum cross-sectional area and hence allow the most water to flow? (b) What depths will allow at least 30 square inches of water to flow? (a) The depth that will provide the maximum cross-sectional area is (b) The depths between in. and inches. 16-2x in. will allow at least 30 square inches of water to flow. 16
P1 = Patm 1 V 7.3 m/s %3D Flow h = 0.96 ft water 3 Density of water 1000 kg/m Determine the pressure at the point 3?
Q1/ This rectangular gate shown in Fig.1 below will open automatically when the depth of water (d) becomes large enough. What is the minimum depth that will cause the gate to open? Fig. (1) 22 200 N 60 -45 m (x 2.4 m)-
: By Bligh's and Lane's theory For the hydraulic structures shown below calculate 1- Sketch the HGL from U/s to D/s 2- Fine the uplift pressure from at key point 3- Find the thickness of floor at point A&B 4m 15m 10m 10m 6m 8m 35 m
2 plates move as indicated with oil on top and water underneath V_T -> h_1 = 1mm h_2 = 2mm V_B = 8 m/s V_T = 2 m/s plate area = 5m^2 liquids SAE-30W Water a) draw velocity profile on vertical dotted line in... b) create a parametric equation for Vw and Vo c) calculate τ between liquids d) calculate force (F=τA)