Answered: 11.44 An abc-sequence set of voltages…

11.44 An abc-sequence set of voltages feeds a balanced three- phase wye-wye system. If V = 440/30° V rms, VAN = 413.28 /29.78° V ms, and Zine = 2 + jl.5 0, find the load impedance.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: Give the value of reactive power per phase seen at load 2.
The following loads are served by a balanced three-phase source: Load 1: 18 kVA at 0.8 pf lagging Load 2: 8 kVA at 0.8 pf leading Load 3: 12 kVA at 0.75 pf lagging. Give the complex power expression for Load 3. Select one: O a. 29.80 +j13.94 O b. O c. 9.00+ j7.94 kVA 6.40 -j4.80 KVA O d. 32.90225.07° KVA O e. 14.40 +j10.80 kVA
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
A three-phase substation bus supplies a wye and a delta connected constant impedance loads. The loads are connected in parallel. A three-phase feeder with an impedance per phase of Z = 0.6+j1.8 Q connects the loads to a source as shown in the one- line diagram of Figure below. The loads draw the following three-phase power: P1 = 35 kW S2 = 30 kVA pfi = 0.90 (leading) pf2 = 0.85 (lagging) wye connected delta connected The line-to-line load voltage is 480 V. Detemine: (a) the impedance of each load per phase, (b) the total line current flowing through the feeder, (c) the line-to-line voltage at the substation bus, and (d) the total three-phase real and reactive power supplied by the bus. Zfeed Vbus
2) Figure shows three loads connected in parallel across a 1000-V (rms), 60-Hz single-phase source. Load 1: Inductive load, ... kVA, 0.28 p.f. lagging Load 2: Capacitive load, ... kW, 40 kvar Load 3: Resistive load, 15 kW Determine the total (a) kW, (b) kvar, (c) kva, and (d) supply power factor. (Please determine the power values within the specified limits: Load 1 apparent power: 100-150 kVA, Load 2 active power: 5-20 kW. By considering the power values you determined yourself, solve the question.) Load Load DE 1 2 Load 3
A balanced delta connected load contains 8 + j4 ohms per phase, while a balanced wye connected loadconsists of 2 – j1 ohms per phase. Both loads are connected in parallel to a three-phase three-wire system inwhich the line voltage is 120 V rms at the loads. The three lines extending from the loads to the source eachhave a resistance of 0.2 ohms. Determine the power lost in the wires.a. 1.42 kW b. 1.38 kW c. 1.24 kW d. 1.83 kW ( please stay on choices, thanks) ..
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
7. For the circuit below, calculate the value of Z₂ for maximum average power transfer to the load. In addition, determine the value of the maximum average power absorbed. (Hint: One approach is to find the open-circuit voltage and the short-circuit current.) j4 2 Vx -j2 n 16 Vx20 4/0° V ZL
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What is the total power drawn from the 3 phase source?
1980628cmid 11616 For reactive load, the power factor is equal to Select one: O a. 1 O b. 90 O c. 2 O d.0 If the voltage V, = 800 mV, then the current flowing in the primary winding Ip is: j2on Select one: O a. None of these O b. l, =40<0° mA O c.l, = 0.320<90° A O d. Ip =320<-90° mA if a Load absorbs an average power of 8 kW at a lagging power factor of 0.5 Select one: O a. -8000 + j13856.4 VA O b. None of these O c. 8000 - j13856.4 VA O d. 8000 - j13856.4 VA estion-299141-3 freactive power is
If a A-connected load has a balanced impedance ZA 94 - 17° 2 and a voltage = = / VBC = 265 82° V rms, what is the magnitude of the current Ia (in A rms)? C V cn Van a Answer: n Von b Ia Ib 20 B IAB IBC ZA ZA ICA C