11.3-18 A long slender column ABC is pinned at ends A and C and compressed by an axial force P (see figure). At the midpoint B, lateral support is pro- vided to prevent deflection in the plane of the figure. The column is a steel wide-flange section (W 250 × 67) with E = 200 GPa. The distance between lateral supports is L = 5.5 m. Calculate the allowable load P using a factor of safety n = 2.4, taking into account the possibility of Euler buckling about either principal centroidal axis (i.e., axis 1–1 or axis 2-2).

11.3-18 A long slender column ABC is pinned at ends A and C and compressed by an axial force P (see figure). At the midpoint B, lateral support is pro- vided to prevent deflection in the plane of the figure. The column is a steel wide-flange section (W 250 × 67) with E = 200 GPa. The distance between lateral supports is L = 5.5 m. Calculate the allowable load P using a factor of safety n = 2.4, taking into account the possibility of Euler buckling about either principal centroidal axis (i.e., axis 1–1 or axis 2-2).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid bar ABC (see figure) is supported by axial bar BD and a pin connection at C. A load P-6000 N is applied at A. Member BD is a 20 mm wide by 9 mm thick rectangular cross-section bar. The pin at C has an allowable shear stress of tallowable = 115 MPa. The overall dimensions of the assembly are a = 110 mm, b= 190 mm, c 50 mm and d= 13 %3D mm. (a) Determine the normal stress in member BD. (b) Determine the required pin diameter at C. B A
A solid steel bar of diameter di = 1.4 in. is enclosed by a steel tube of outer diameter d3 = 2.25 in. and inner diameter d2 = 1.9 in. (see the figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar, which has length L = 26 in., is twisted by a torque T = 5,100 lb-in. acting on the end plate. Tube A Bar End plate (a) Determine the maximum shear stresses T1 and T2 in the bar and tube, respectively. Round your answers to the nearest whole number. T1 = psi T2 = psi (b) Determine the angle of rotation (in degrees) of the end plate, assuming that the shear modulus of the steel is G = 11.5 × 10° psi. Round your answer to three decimal places. (c) Determine the torsional stiffness kT of the composite bar. Round your answer to the nearest whole. [Hint: Use equations below to find the torques in the bar and tube.] T = T GIp, + G2IP, kT = k-in.
The beam shown in the figure has a roller support at A, a fixed support at C and an internal hinge at B. The lengths of segments AB and BC are a and b respectively. A uniformly distributed load, q, is applied between points B and C, and a concentrated load P acts at a distance a/2 from the support A. EI is constant. a/2 P por quity A B Figure 2: Beam with internal hinge Determine the expression for the elastic curve (v(x)) for segment BC using the method of superposition. Use a = 2 m, b = 3 m, E = 70 GPa, I = 198 × 106 mm4, P = 10 kN and q = 2 kN/m.
The figure below shows a section of a column subjected to load P, which is applied 50 mm from the midline of the section's web. The column is made from material, which has an allowable normal stress of 180 MPa (both in tension and compression). The area of the section is 10050 mm?; the principal moments of inertia Imar = 146.554x106 mm and Imin 20.076x10° mm*. !! Determine the maximum allowable load P. 15 mm 150 mm 15 mm 150 mm 50 mm 15 mm 100 mm 100 mm 1194.6 kN 363.6 kN 1809.0 kN O 516.4 kN O 189.5 kN
5. Determine the allowable axial load PA for a W250 x 67 steel wide-flange column with pinned ends (see figure below) using a Factor of Safety n=1.5 for the following lengths: L-3 m, 5m, 8 m and 10 m. Assume E-200,000 MPa, and G-300 MPa. 7 L A Pl A ISTE Section A-A
A steel bar with a circular cross section, AC, is built in at both ends (A and C) and is subjected to a 300N point load at B, 300mm from point A, as shown in the figure below. The bar has a diameter of 8 mm and the material has a Young's modulus of 200GPa. Determine the magnitude of the reaction force at A? O O O O 380 N 150 N Don't Know 210 N 300 N 300mm B 300 N 700mm
The simply supported beam shown in Figure 1 (see next slide) spans a distance of L = 6 m and carries two concentrated loads P, which are applied at a distance of a = 1.5 m from the supports. The beam is fabricated by bolting a steel plate between two wood planks (see Figure 2). The wood planks each have dimensions of b = 30 mm and d = 240 mm. The steel plate has dimensions of t = 9.5 mm and d = 240 mm. The moduli of elasticity of the wood and the steel are 12.5 GPa and 200 GPa, respectively. a) Determine the maximum bending stresses produced in the wood planks and the steel plate if P = 8 kN. b) Assume that the allowable bending stresses of the wood and the steel are 8.25 MPa and 150 MPa, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.)
The frame ABC consists of two members AB and BC that are rigidly connected at joint B, as shown in part a of the figure. The frame has pin supports at A and C. A concentrated load P acts at joint B, thereby placing member AB in direct compression. To assist in determining the buckling load for member AB, represent it as a pinned-end column,as shown in part b of the figure. At the top of the column, a rotational spring of stiffness βR represents the restraining action of the horizontal beam BC on the column (note that the horizontal beam provides resistance to rotation of joint B when the column buckles). Also, consider only bending effects in the analysis (i.e., disregard the effects of axialdeformations).(a) By solving the differential equation of the deflection curve, derive the buckling equation for this column:[βRL/EI](kL cot kL-1) - k2L2=0in which L is the length of the column and EI is its flexural rigidity.(b) For the particular case when member BC is identical to member AB, the…
A uniform concrete slab of total weight W is to be attached, as shown in the figure, to two rods whose lower ends are on the same level. Determine the ratio of the areas of the rods so that the slab will remain level. Figure P-215 Steel E - 29 x 10 psi Aluminum E - 10 x 10 psi L- 4 ft L-6R Total Weight = w 3 ft 6 ft The value of the load P at the aluminum 0.33 W b. 0.67 W с. W d. none of the above The ratio between the internal reactions of the aluminum and the steel 2.03 b. 0.49 c. 0.67 d. none of the above The ratio between area of steel and area of the aluminun 0.867 b. 0.409 c. 0.258 d. none of these If the value of W is limited to 1500 lb, which of the statements is true? The maximum load the steel can carry is greater than of the aluminum The maximum load the aluminum can carry is greater than of the stell The sum of loads at the steel and the aluminum is twice the value of steel The deformation developed at the steel is greater than that of aluminum If the cross-sectional area…
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 °C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 C. Steel A-36 A =160 mm? 3,5m 10 kN/m 3 m 3m 2 m 2014-T6 Aluminum A =200 mm E A,
tekst Flytt fremover v P Juster v Bildestiler S Tilgjengelighet Ordne Beam AB in the figure is clamped at end A and has a plain bearing at end B (See figure). The beam has one length egual to L and is subjected to an evenly distributed load equal to q. B a) Use the unit load method to solve the statically indeterminate task and prove that the vertical the stock reaction in B is equal to 3qL/8. b) Assume L = 8m, q = 15kN / m, draw moment and shear force diagram D Fokus 10°C