11.21 (B). Derive the formulae for the slope and deflection at the free end of a cantilever when loaded at the end with a concentrated load W. Use a strain energy method for your solution. A cantilever is constructed from metal strip 25 mm deep throughout its length of 750 mm. Its width, however, varies uniformly from zero at the free end to 50 mm at the support. Determine the deflection of the free end of the cantilever if it carries uniformly distributed load of 300 N/m across its length. E 200 GN/m2. [1.2 mm.]

11.21 (B). Derive the formulae for the slope and deflection at the free end of a cantilever when loaded at the end with a concentrated load W. Use a strain energy method for your solution. A cantilever is constructed from metal strip 25 mm deep throughout its length of 750 mm. Its width, however, varies uniformly from zero at the free end to 50 mm at the support. Determine the deflection of the free end of the cantilever if it carries uniformly distributed load of 300 N/m across its length. E 200 GN/m2. [1.2 mm.]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Mention correct options with solution
Qus
A square bar AB with an allowable stress of 32 MPa is attached to a hollow tube BC. Compute the inside diameter of the hollow tube BC if the allowable stress is limited to 220 MPa. P. A B Cross Section of AB Cross Section of BC 50 mm ODI s0 mm 50 mm
1. A circular flat plate of diameter 120 mm and thickness 10 mm is constructed from steel with E = 208 GN/m² and v=0.3. The plate is subjected to a uniform pressure of 5 MN/m² on one side only. If the plate is clamped at the edges determine: (a) the maximum deflection; (b) the position and magnitude of the maximum radial stress.
Q.43 Consider a steel (E = 200 GPa) column hinged on one side and fixed on the other side. Its height is 1.5m and the cross-section is 20 mm x 25 mm. The Euler's critical stress(in N/mm²) is...
1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula) and the transversal displacement of section A. The allowable stress of the beam material is considered of 100MPa. The cross section of the beam is given in the next figure. q-5KN/m M=4KNM F=3KN L1=3m L2=1m L3=1m 8t M F JA 10t 2t L1 L2 L3 2t 4t
7
Solve it correctly please. I will rate accordingly.
A cube of side 100 mm is subjected to an axial compressive load of 200 kN. Its lateral strain is prevented by applying uniform pressure but only one fourth of lateral strain could be prevented, then which of the following statements is/are correct? Assume E = 200 MPa and μ = 0.3. A The decrease in length in direction of load after applying pressure is 9.358 x 10-3 mm. B The uniform pressure applied has a value of 8.57 N/mm². C The uniform pressure applied has a value of 2.14 N/mm². D The increase in length in lateral direction after applying pressure is 2.25 x 10-³ mm.
please draw a proper free body diagram and answer in full solution all questions
The beam is subjected to a bending moment of M = 17 kN. m. σA = B 200 mm OB = 30 mm 30 mm M 30 mm 30 mm 50 mm 150 mm 150 mm 50 mm Part A Determine the bending stress in the beam at point A. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: Q Tap image to zoom Part B Determine the bending stress in the beam at point B. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: