11 Given the following well design: a) Calculate total hole volume with the entire drill string in the hole. bbls b) Calculate total hole volume with the entire drill string out of the hole. bbls CSG Specification: (13 3/8" CSG (12.5" ID) and 7" Liner (6" ID)) Drill Pipe Specification: (4.5" DP (3.5" ID))

11 Given the following well design: a) Calculate total hole volume with the entire drill string in the hole. bbls b) Calculate total hole volume with the entire drill string out of the hole. bbls CSG Specification: (13 3/8" CSG (12.5" ID) and 7" Liner (6" ID)) Drill Pipe Specification: (4.5" DP (3.5" ID))

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Step boring is advised to be used for: a/Machining large radial depth of cuts b/Machining hard materials c/Rapidly roughing surfaces with tolerance class of IT9 or higher
m) what is the block shear rupture (L-shaped) capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
A split-barrel sampler is driven 24 inches in 6 in. increments. The SPT blow counts recorded were 2-3-4-6. Determine the measure SPT resistance value based on the blow counts. Oa 35 Ob7 Oc 15 Oa 10
Step 1 given; What the dismantling and Assemble of diaphragm valveAlso what is function of part than constant it Step 2 solution; Dismantling joint-It is very useful for joining and removing of pipe section with designing of dismantling joint. because its is used for joint longitudinal adjustment in pipe section for joining of pipe. without longitudinal adjustment ,It is not possible to insert valve for joining of longitudinal pipe. Diaphragm valve-diaphragm valve is flexible valve. which is used for controlling pressure when force is applied in valve then it will be automatically open or close on the basis of pressure adjustment. and it will control the flow rate of fluid. when less flow rate required then valve slightly closed on the basis of flow requirement. when more flow rate required then it will be open. function- it will change the speed and velocity of fluid.
Please include FBD in your solution
Determine the design capacity using ASD and NSCP specifications for the connection shown. Use A36 steel and D20 diameter bolt on an oversized hole 117 75 75 diameter. Show complete solution and round your final answer to the Pu OR nearest thousandths. PA 125 Given formula: Nominal hole diameter Due GSY: Bolt Hole diameter ØPn = ØA,F, ;ø= 0.90 dnet diameter Standard Oversized Due TRS M16 18 20 + 2mm ØP, = ØUA„Fu ;ø= 0.75 M20 22 24 + 2mm M22 24 28 + 2mm U = 1- M24 27 30 + 2mm Due to BSS ØRn = Ø[0. 60A,nyFu + U psAntFu] < ø[0.60A9„F, + UbgAntFu] ; ¢ = y -X = 14.35 mm 0.75 Slendemess Ratio < 300 ; C8x18.75 I'min For section properties I = Iox + A(y²) ly = Ioy + A(x²) A, = 3,555 mm? bf = 64.2 mm tf = 9.9 mm tw = 12.4 mm d = 203.2 mm ly = 18.31 x106 mm* Ix = 0.82 x106 mm* r = 008 75 75
7. /8 Using the figure below, answer the following: a. What type of weld is to be made? b. What is the significance of the square on the reference line? c. What is the depth of preparation on the arrow side? d. What is the effective size of the weld on the other side? True (³²³)
Q2/ Choose the correct answer. 1- The bit is connected to the lower end of the - A- drill pipes B-drill collars C-drill string. is a casing string that does not extend back to the wellhead, but is hung from another 2- casing string A- production casing B- intermediate casing C- liner. 3- traveling block and drilling line is called A- Drawwork B-block tackle C-rotary system 4- The drawwork is located at A- the derrick floor B-the mast C-the substructure 5- Objective of A- Relief well B-side tracking well. C- controlling vertical well. Solve all ---well is to intercept the borehole of a well for killing purpose
I thought it was the opposite. Why is the steel rod the diameter of the tube?
3. For the hanger in question 2, consider that the tension member is a plate of grade 350W material connected to a gusset plate, as shown below. Determine the required thickness of the plate with a width of 150 mm considering 4 M24 centred bolts with a pitch distance of 65 mm and end distance of 45 mm. Assume that the holes are drilled. Activa Click M C
.
1. Discuss the characteristic and limitation of the following hand tools. A.) Angle Grinder B.) Bench/Pedestal Grinder 2. Discuss the characteristic and limitation of the following: A.) Impact wrench B.) Pneumatic hacksaw 3: Discuss the characteristic and limitation of the following hand tools: A.) Drill press B.) Electric circular saw