The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If the allowable shear stresses for the magnesium and steel are (Tallow)mg = 45 MPa and (Tallow)st = 75 MPa, respectively, determine the maximum allowable torque that can be applied at A. Also, find the corresponding angle of twist of end A. O O 900 mm 80 mm/ 40 mm T

The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If the allowable shear stresses for the magnesium and steel are (Tallow)mg = 45 MPa and (Tallow)st = 75 MPa, respectively, determine the maximum allowable torque that can be applied at A. Also, find the corresponding angle of twist of end A. O O 900 mm 80 mm/ 40 mm T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft, which is fixed at both ends, is composed of Aluminum shaft ABC (Gal = 24 GPa, d = 50 mm), steel sleeve AB (Gst = 76 GPa, dout = 90 mm), and copper sleeve ABC (Gcu = 45 GPa, dout = 75 mm), which are all welded together. Considering the allowable shear stresses (Tal, Ist, Tcu), determine the maximum allowable torque T (kN-m) that may be applied at B as shown. Note: Double-headed arrows follow the direction of the thumb when using the right-hand rule. A Parameters Tal = 51 MPa Tst = 101 MPa Tcu = 71 MPa steel Cu AI L = 5m B ➡T Cu AI L= 3.5m C
Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
Principle of superposition The beam is indeterminate to the first degree. Force in member BD is chosen as the redundant. This member is therefore sectioned to eliminate its capacity to sustain a force. 60 kN/m 3 m 1.8 m 60 45 actual structure (a) 160 kN/m B FaD redundant рrimary structure ARD FRp applied Fap D
2
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
Part (b) (A hollow circular steel drive shaft has an outer radius of R mm and an inner radius of r mm as shown in Figure Q9-b. Figure Q9-b: Given that r-16, R-30 and the maximum allowable shear stress in the shaft is 75 N/mm2, calculate the maximum permitted torsional moment, T., that can be transmitted by the shaft. T: [(b)
13