Round answers to the nearest hundredths. Compressibility11) A liquid compressed in a container has a volume of 1 Liter at a pressure of 1 MPa and a volume of 0.995 Liter at apressure of 2 MPa. What is the modulus of elasticity (Ee) of the liquid?12) What pressure is required to reduce the volume of water by 0.6 percent? Bulk modulus of Elasticity of water, Es is2.2 GPa.13) A rigid container is partially filled with liquid at 15 atm. The volume of liquid is 1.232 L. At a pressure of 30 atm, thevolume of liquid is 1.231 L. Find the bulk modulus of elasticity of the liquid over the given range of pressure if thetemperature after compression is allowed to return to its initial value. What is the coefficient of compressibility? Note: 1atm = 101.325 kPa.

Answered: Image /qna-images/answer/b4c7c4b7-b1cf-41d2-9de1-12feb14c123f.jpg

Answered: 11) A liquid compressed in a container…

11) A liquid compressed in a container has a volume of 1 Liter at a pressure of 1 MPa and a volume of 0.995 Liter at a pressure of 2 MPa. What is the modulus of elasticity (En) of the liquid?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Related questions

Q: (Figure 1) igure y 3 in. 3 in. 1 of 1 Part A Determine the product of inertia of the shaded area…

Q: Given that: V= $¹5 2√√7 where V is the volume of a sphere and S is its surface area. Determine S,…

A: Given that:V = (S1.5) / (2√π)V is the volume of a sphereV = 780 * 10-3 * m3 S is its surface area.

Q: Choose the answer that shows 80 chains converted to miles. O 0.5 mile 1 mile O 2 miles O 1.2 miles

A: Answer 1 mile

Q: QUESTION 2 The sides of a closed figure have been measured and found to have a total lenght of…

Q: Shiela performed a number trick to Bryan. She let Bryan pick a number divisible by two. She then…

A: Asked: To determine the Shiela told Bryan.

Q: The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the…

A: given- radius=R=5 cm area=A % error in area needs to be find out.

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

Round answers to the nearest hundredths.

Compressibility
11) A liquid compressed in a container has a volume of 1 Liter at a pressure of 1 MPa and a volume of 0.995 Liter at a
pressure of 2 MPa. What is the modulus of elasticity (Ee) of the liquid?
12) What pressure is required to reduce the volume of water by 0.6 percent? Bulk modulus of Elasticity of water, Es is
2.2 GPa.
13) A rigid container is partially filled with liquid at 15 atm. The volume of liquid is 1.232 L. At a pressure of 30 atm, the
volume of liquid is 1.231 L. Find the bulk modulus of elasticity of the liquid over the given range of pressure if the
temperature after compression is allowed to return to its initial value. What is the coefficient of compressibility? Note: 1
atm = 101.325 kPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.
Calculate the R-value for the following materials: a. 4 in. thick brick b. 10 cm thick brick c. 12 in. thick concrete slab d. 20 cm thick concrete slab e. 1 cm thick human fat layer
Bourdon-type pressure gauges are used in thousands of applications. A deadweight tester is a device that is used to calibrate pressure gauges. Investigate the operation of a deadweight pressure tester. Write a brief report to discuss your findings.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Determine the specific gravity of the following materials: gold ( = 1208 lb/ft3), platinum ( = 1340 lb/ft3), silver ( = 654 lb/ft3), sand ( = 94.6 lb/ft3), freshly fallen snow ( = 31 lb/ft3), tar( = 75 lb/ft3), hard rubber ( = 74.4 lb/ft3).