11- A horizontal cylinder is fitted with a frictionless piston has a cross section area of 0.2 m². The cylinder contains 1 kg of air at 20 °C. The cylinder is heated by an amount of 131.65 kJ. The piston is observed to move slowly through a distance of 0.5 meter against the atmospheric pressure of 1 bar. The net work done by the gas during this time is 50 kJ. Calculate the final temperature of the air at the final state.

11- A horizontal cylinder is fitted with a frictionless piston has a cross section area of 0.2 m². The cylinder contains 1 kg of air at 20 °C. The cylinder is heated by an amount of 131.65 kJ. The piston is observed to move slowly through a distance of 0.5 meter against the atmospheric pressure of 1 bar. The net work done by the gas during this time is 50 kJ. Calculate the final temperature of the air at the final state.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state temperature T2.__________ (K)
3000 kJ of heat is given to 1 kg of water at 20 C. If steam with a pressure of 750 kPa is obtained as a result of this process, is this steam wet?institution? You should reach the result by typing the table values and operation steps. TIP: You should decide on enthalpy values using Thermodynamic Property Tables.
A certain ideal gas with initial conditions of 0.1 m3 and 6 bar expands isothermally to 0.5 m3. Calculate the final pressure during the process. Give answers in kJ and kPa.
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state pressure p2.__________ (kPa)
2) Two glass bulbs, one on the left with a volume of 2 liters and the other on the right with avolume of 6 liters, are connected to one another by a thin tube that is initially closed by astopcock. The bulb on the left has 0.1 moles of ideal gas, and the bulb on the right isevacuated. The system is in thermal equilibrium with the surroundings at 300K. When thestopcock is opened, the gas flows out to fill both bulbs. Calculate A for this process. If wewere to insert a propeller to extract work as the gas flows from left to right, what is themaximum amount of work that we could possibly extract?
Air as an ideal gas is contained in a piston/cylinder system constrained by a non-linear spring. Initially the gas in the cylinder is at 100 kPa, which is balanced by the atmospheric pressure outside of the cylinder (the weight of the piston is negligible). The force on the spring at the start is zero. The spring force is F=kx². k=600. kNt/m². The cross-sectional area of the piston is 1 m², the initial volume is 1 m³, and the initial temperature is 300 K. Heat is added until the volume of the gas has expanded to 1.5 m³. Find: (a) The work done by the gas on the face of the piston (kJ). (b) The final temperature (K). (c) The amount of heat added (kJ). Hint: This problem is easiest if you calculate the spring work and the atmospheric work separately. Air V₁=1.0 m³ Piston Area = 1.0 m² T₁=300 K P₁=100 kPa Atmospheric P on upper piston face= 100 kPa
Use image below Part A - Evaluate the volume and internal energy of the air in the initial state 1, in the intermediate state 2, and in the final dead state DS. Also evaluate the temperature of the air in the intermediate state 2. PArt B - Plot the processes 1 → 2 → DS on P–v, T–v, P–s, and T–s diagrams. Mark states 1, 2, and DS on the graphs, and make sure that it is clear when a given quantity increases, decreases, or remains constant.
2. In a free-moving piston-cylinder assembly with a pressure of 60 kPa and a temperature of -20°C100 grams of R-134a is initially retained. until the assembly temperature is 100°C.is heated. Calculate the volumetric change after heating.
The compression factor for low molecular-weight, real gases at very low pressure is,
Please show correct solution and clear explanation. Choose from the choices for the correct answer. Thank you.
I need the answer quickly
Show detailed work. No Chatgpt,Only Handwritten.