Steam at 130 bar has a specific volume of 0.1726 m³/kg. Determine the temperature, the pecific enthalpy, and the specific internal energy. If the specific volume increased to the 0.1901 m'kg at same pressure. Determine the emperature, specific enthalpy and specific internal energy and analyze the results obtained form (a) and (b).

Steam at 130 bar has a specific volume of 0.1726 m³/kg. Determine the temperature, the pecific enthalpy, and the specific internal energy. If the specific volume increased to the 0.1901 m'kg at same pressure. Determine the emperature, specific enthalpy and specific internal energy and analyze the results obtained form (a) and (b).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 1500L tank contains benzene at a pressure of 400kPag and a temperature of 320K. Later, because of leak, it was found that the gauge pressure has dropped to 320kPag, and the temperature has decreased to 300K, determine the amount of benzene that has leaked out.
Determine the volume flow rate and the density of carbon dioxide at the inlet and the volume flow rate at the exit of the pipe using (a) the ideal-gas equation and (b) the generalized compressibility chart. Also, determine (c) the error involved in the first case.
Ten pounds of water at 35oF, and 6.00 lb of steam at 250oF and 20 psia are mixed together in a container of fixed volume. What is the final temperature of the mixture? How much steam condense? Assume that the volume of the vessel is constant with a value equal to the volume of the steam and that the vessel is insulated.
The equipment room housing the compressor and condenser of a refrigerant ammonia system has dimensions 5 by 4 by 3 m at 1 bar room pressure. Calculate the maximum volume of the refrigerant in m3 which would have to escape into the space to cause a toxic concentration for a 1/2-h exposure.
where are you finding v=0.0159939 m3/kg ? , when I look for the specific volume for saturate steam at 11000 kpa , I am finding vg=15.987 ?
A piston-cylinder device contains satuated water vapor with a constant pressure. The mass and the pressure are listed in the table below. The water is heated by a resistance heater (see the picture below) within the cylinder. The heat supplied by the heater is given in the table below. The cylinder is insulated so there is not heat loss. (a) Determine the enthalpy per unit mass after the water vapor received heat. (b) Determine the temparature after the water vaopr received heat. Parameter Pressure Mass of water Heat supplied by the heater Unit kPa g KJ Value 300 26 7.1 heater
Change enthalpy of argon (mol wt = 40) when it is heated from in 25°C to 100°C is kJ/kg.
How much energy (BTU) is given off when 5 lbm of saturated steam with a quality of x=1 at 1 psia? How does this compare with the same mass condensing at atmospheric conditions?.
Physics Consider a tank full of gaseous propane at 25 ºC and 5 atm. The tank is accidentally damaged resulting in a 10-mm hole. Calculate the mass flow rate of propane through the hole (assume that the pressure in the tank remains at 5 atm and that the ambient is at atmospheric pressure). NB: the ratio of specific heats for propane is 1.15
CO2 gas enters the pipe at a flow rate of 2 kg / s, 3 MPa pressure and 500 K temperature. While the CO2 pipe type is flowing, it is cooled down at constant pressure and its temperature drops to 450 K at the pipe outlet.Volumetric flow of CO2 at the pipe inlet,Using the generalized compressibility diagram, find
Question : Determine the units of the quantity s ̄/Ru, where s ̄ is the molar specific entropy and Ru is the universal gas constant. Explain your answer please
2.5 kg of Steam at 500 kPa and 400oC was cooled in a piston cylinder device until 84% condenses.. What is the amount of entropy generated (kJ/K)?