*11-72. The reactikın of the ballast on the milway tie can beassumed uniformly distributed over its length as shown. If theWOod has an alkiwable bending stres of odetermine the required minimum thicknesstof the rectangularcros sectional area af the tie to the nearest multiples of 5 mm.= 10.5 MPa,75 AN75 LND45 m-15:

Apply condition of equilibrium to find the udl load ∑Fy=075+75-w(2.4)=0w=150/2.4=62.5 KN/m

Answered: *11-72. The reactikın of the ballast on…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6-122 Segment A of the composdte heam is made from 2014-T6 aluminum alloy and segment Bs A-36 steel. If w - 0.9 kip/, determine the absolute maximum bending stress developed in the aluminum and steed. Skelch the stress distribution on the cross section. 6-123. SegmentA of the composite beam is made trom 2014-T6 aluminum alkoy and segment B s A-36 steel. The alowable bending stress for the aluminum and steel are (a)¬15 ksi and (a -22 k.Determine the maximum alowahle Intensity w of the uniform distributed kad. -15 h Probs. 6-122/123
6-125. The wooden section of the beam k reinforced with two sted plates as shown. Determine the maximum internal moment M that the beam can support If the allowable streses for the wOd and steel are (oo-6 MPa, and (alol - 150 MPa, respectively Take E- 10 GPa and E-200 GPa
Determine the internal forces (axial force, shear force, and bending moment) at point j of the indicated structure, teta = 0 º
The L-shaped frame is made from two fixed-connected segments. Determine the horizontal displacement of the end C. Use the method of virtual work. EI is constant.
If the extended stress at the point p in the level and at i+j+ k is given by matrix 10 2 2 22 the component Tnx = 231 1 %3D nx V3 nx V3 aņl wrong %3D
F6-9 II Lhe heam is suhjecied to a bending moment of M= 20 N-mL determine the manimum tending sires In the beam. 200mm 20 20m F6-18. the heam is subjeced lo a bending moment of M= 50 EN - m. skeich the hending siress disiribution over the beam's croSS Seclion. 30 mm 150 mm 130 ma
The steel tube has an elliptical cross-section of mean dimensions shown and a constant thickness of t = 0.2 in. If the allowable shear stress is tallow = 8 ksi, and the tube is to resist a torque of T = 250 lb # ft, determine the necessary dimension b. The mean area for the ellipse is Am = pb(0.5b).
Hwi Abeam had subjected to a postive bending moment of 5 KN.m. Thc Coss-Sedional dimensious are shown below. Draw the bending stress distribution ou the Cross- sedion. loo mm 15 mm T 3 mm
6-109. The box beam is suhjucted to the internal moment of M = 4AN m, which is directed es shown. Determine the maximum bending stress developet in the beam and the orientalion of the neutral axk 6-110. E the wENd used for the bIx beam has an alkwahle hending stresm of (a=6 atowahle internal moment Mthat can he appliod to the heam. MPa, determine the maximum 25 mt mm 150 men 50 150 am Probs. 6-1NI10
F7-7. Two klentical 20-mm thick plates are bollad to the top and bottom lange to form the buili-up heam. II the beam is subjected toa shear force of V = 300 KN, determine the allowable maximum spacing s of the boits to the nearest mm. Each bolt has a shcar strength of 30 RN. F7-9. The boards are boltod together to form the bull-up heam. Ir the beam is suhjactad to a shear force of V = 15 kip. determine the allowahle maximum spacing of the bolts le the nearst in. Each bolt has a shear strength of 6 kip. I in 05 in. 200 mm 3 in. 10 m 300 mm 10 mm 20 mm 7-9 FL7
The man has a mass of 100 kg and center of mass at G. If he holds himself in the position shown, determine the maximum tensile and compressive stress developed in the curved bar at section a–a. He is supported uniformly by twobars, each having a diameter of 25 mm. Assume the floor is smooth. Use the curved-beam formula to calculate the bending stress.
Determine the vertical displacement of joint C. Assume the supports at A and E are pins and joint C is pin connected. EI is constant. Use the method of virtual work.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS