"6-120. The composite beam is made of steel (A) bondedto brass (B) and has the cros section shown. IIt is subjectedto a moment of M - 65 KN - m, determine the maximumbending stress in the brass and steel. Alsa, what is the stresIn cach material at the seam where they are bondedtogether? E- 100 GPa, E-20O GPa.6-12L The composile beam is made of steel (A) bonded tobras (8) and has the cros section shown. II he alkwablebending stress far the sted is (oae- 180 MPa, and for thebras (oa-0 MPa, delermine the matimum moment Mthat can be appiled to the beam. -100 GPa, E-200 GPaImimY200 mm175 mProbs. 6-12121

Answered: Image /qna-images/answer/23e2676e-c64a-4d3b-869f-1c2754fda660.jpg

6-12L The composile beam s made of steel (A) bonded to bras (8) and has the aros section shown. II the alkwable bending stress for the sted is (a)e – 180 MPa, and Sor the bras (o - 60 MPa, delermine the matimum moment M that can be appiled to the beam. -100 GPa,E-200 GP mim 200 mim M 175

6-12L The composile beam s made of steel (A) bonded to bras (8) and has the aros section shown. II the alkwable bending stress for the sted is (a)e – 180 MPa, and Sor the bras (o - 60 MPa, delermine the matimum moment M that can be appiled to the beam. -100 GPa,E-200 GP mim 200 mim M 175

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A composite beam is made of two brass [E = 107 GPa] plates bonded to an aluminum [E = 65 GPa] bar, as shown. The beam is subjected %3! to a bending moment of 1890 N-m acting about the z axis. Assume b=59 mm, d,=49 mm, d2=10 mm. Determine: (a) the maximum bending stresses opr, oal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) dz Aluminum (1) Brass (2) dz b Answers: (a) Obr = i MPa, oal = i MPa. (b) Obri i MPа.
The cross section of a composite beam madeof aluminum and steel is shown in the figure. The moduliof elasticity are EAl = 75 GPa and Es =200 GPa.(a) Under the action of a bending moment that producesa maximum stress of 50 MPa in the aluminum,what is the maximum stress σs in the steel?(b) If the height of the beam remains at 120 mmand allowable stresses in steel and aluminum aredefined as 94 MPa and 40 MPa, respectively,what heights hAl and hs are required for aluminumand steel, respectively, so that both steeland aluminum reach their allowable stress valuesunder the maximum moment?
y M B H B W Figure-2 A wide flange beam is subjected to a moment as shown in Figure-2. If M=10 kN.m, H=212 mm, W=170 mm, d=11 mm, t=18 mm and 0=64°; Btermine the momentOt lhadat about the axis- etermine the mement of inertia (mmabeut the avie y Betermine the normat stress (MPa due to bendng atpontA itic commressIive stress use Determine the orientation angle, B (degree), of the neutral axis relative to the +z axis.
70 mm Mx G 165 mm Mx = 79ヒNm %3D 60 mm 190m Mx affects the cross section digure. Calculate the noral stress values The bending moment of the beam given in n that will occur at the points I,2, 3 of the beam sectio and draw the noral stress distribution.
Please solve this question again. I think previous solution was incorrect
A uniform distributed load of 4 kN/m is applied to a cantilever beam as shown. What is the resisting bending moment equation for any section of the beam? 4 kN/m Select one: O a. M, = -2x³ kNm O b. Mr = -2x² kNm O c. M₁ = -4x² kNm O d. Mr = -8x kNm O e. None of these options Ai →X 2M
Hwi Abeam had subjected to a postive bending moment of 5 KN.m. Thc Coss-Sedional dimensious are shown below. Draw the bending stress distribution ou the Cross- sedion. loo mm 15 mm T 3 mm
Picture given below; There is a uniformly distributed load on the beam, which is made of Al2010 (T4) alloy T-profile and is connected to the "A" sliding bearing with "B" joint fixed support. Safe compression and tensile normal stress of the beam is Gemn=100 MPa. q=23 kN/m C-C Kesiti + 15 | 18 | 15 q=23 kN/m A유 30 cm 100 cm 150 cm 16 KİRİŞ T- PROFİLİ 74 Ød MAFSAL PİMİ Ölçüler mm dir. 104 S-1) Calculate the support reactions by drawing the SCD of the beam. S-2) The beam; a) Draw the shear force diagram, b) Moment diagram and determine the maximum moment. S-3) Find the x and y axis coordinates of the center of gravity of the cross-sectional area of the beam whose T-profile dimensions are given. S-4) Find the moments of inertia with respect to the vertical and horizontal axes passing through the center of gravity of the T-profile cross-section area. S-5) Find the tensile and compression stresses caused by bending on the beam with T-profile and check the safe carrying condition of this…
Show COMPLETE SOLUTIONS Draw FBD
B d₁ dz A M₁ d3 A copper core is bonded to a steel tube. The inner and outer diameters of the steel tube are d₂ = 90 mm and da = 45 mm, respectively. The copper and steel have shear moduli of Geu = 24 GPa and Gst = 75 GPa. If a moment of M₁ = 600 Nm is applied at the end of the composite shaft, find a. The portion of the applied moment carried by the steel tube Tat= Nm b. The portion of the applied moment carried by the copper core Teu = Nm c. The maximum shear stress in the steel tube Tst= MPa d. The maximum shear stress in the copper core Tex = MPa
5
Final the shooring force and Bendling Moment Diogram of the following beam: oKN -2m. 2m 5KN