10V R1 R3 ww R2 R5 R6 Circuito 1 R1 R2 R4 m R3 15V R1 20V R4 R5 R6 Circuito 3 Considere: R1=1k0, R2=2.2kN, R3=3.3kN, R4=4.7km, R5-5.6km, R6=6.8k R2 R5 Circuito 2 R1 R2 10V www R3 R3 www R6 R4 R6 Circuito 4 R4 R5

Q: a) In the circuit shown it is given that ß=120. Calculate the IE and VE 6V 4 330K VE 1.2K V-6V

A: In this question, we need to determine the current IE and voltage VE as shown in the circuit.

Q: The current in the following circuit was measured and found to be 2 mA. R1 R2 2k Ohm 3k Ohm .12V R3

A:

Q: What is the circuit used for? What is the measuring device in this circuit measuring?

A: The given circuit arrangement is shown below.We need to tell the use of the circuit and the name of…

Q: Determine the voltage dropped across R3

A: In the given questions we need to calculate the voltage across resistor R3.

Q: All voltages and currents present.

A: In this question We need to determine the voltage and current across the each resistance.  We are…

Q: -) In the following circuit using Kirchhoff's find: a) The current in each branch of the circuit. b)…

A:

Q: -4. Assume a total current of 2 amperes flows in a circuit with three resistors. R1 has a value of…

A:

Q: The current ia in the circuit shown is 20 A. Find (a) io; (b) ig; and (c) the power delivered by the…

A:

Q: QUESTION 2 ow many address lines are used in the entire sys elow? Type out the number, for example:…

A:

Q: What is the total area for the following Aluminum wire run? Six - 350 KCMIL XHHW Stranded Two -…

A: b) 3.7542 in²   To find the total area for the given Aluminum wire run, we need to calculate the…

Q: 1. a) Given that E = 15a, charge density at that point? Assume ɛ=ɛ0 b) Evaluate V X A and V VX A if:…

A:

Q: 1) In the following circuit find: a) All of the currents and voltages. b) The power dissipated in…

A: In this question,  We need to determine the currents and voltage across the each resistance. And…

Q: Please complete the circuit below given the following data.

A: The voltage across any resistor follows the ohm's law V=IR, where V is the voltage across the…

Q: R1 R3 1ko 2500 R4 R5 R2 1.2ka 1.5ka -10V 3300 5800 R6 R7 2000

A: To determine voltage, current and power of all resistors

Q: Shown in the figure below is an electrical circuit containing three resistors and two batteries. I₁…

A: For the given circuit we have to write the Kirchhoff loop equation for perimeter in clockwise and…

Q: I need  the voltage drop across R2 for v2

A:

Q: Q1). If the switch number 1 is closed and 2 is open what voltage would you measure at : i). V1 ii).…

A:

Q: Find the maximum power transferred to the load resistance (RL). ww 100 10V

A: Given circuit,

Q: The voltage drop across 1.50 resistor in the circuit shown below is 1.50 19 1.929V 2.572V 3.215V…

A: Apply kvl in loop to find current in the loop. Now using ohms law calculate voltage across the 1.5…

Q: Data: R1 = 30 R1 R2 = 20 3 2 R3 = 80 U V = 7 V 7 V What is the equivalent resistance value of this…

A: The circuit can be made as: The resistance R2 and R3 are in parallel. So, the equivalent of the two…

Q: If every resistor in equals 2.2k, what is the value of RT?

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.