10V b 15V 5Ω www f d 20V 102 h

Q: Determine the possible flows in the network shown in figure below.And solve a system of linear…

A: possible flows in the network shown in the figure below are determined

Q: Using 24v AC source design a 24v unregulated power supply circuit that will power a 1kohms load with…

A: Given: C=480μFR=1kΩVm=24VRipple voltage=50 mVT=1ms

Q: 6. Transformers have the capability to step up or step down AC voltage True False

A:

Q: 4) If the capacitances of a 3-phase belted cable are 21 µF between the three cores bunched together…

A:

Q: Using Kirchhoff's voltage law, . you can find the voltages across certain parts of a series-parallel…

A:

Q: The bridge method commonly used for measuring mutual inductance is: A. wheat stone bridge B. Wien…

A: Given Bridges, A. wheat stone bridge B. Wien bridge C. De Sauty bridge D. Heaviside campbell bridge

Q: Four conductors meet at a junction. the current are i1= 5sinwt, i2= 3sin(wt + 90) and i3=…

A: The solution can be achieved as follows.

Q: Two coils wound on a common core have L1=0.2 H, L2=0.5 H, and M=0.1 H. The currents are…

A: Given data, The value of inductor L1 = 0.2 H. The value of inductor L2 = 0.5 H. The value for…

Q: A E₂ R2 R₁ F E E D₁ S с R3 E3 Equating E3 C Ec HH R₂

A: Anderson's bridge:- It is a type of AC bridge which is used to determine self inductance of…

Q: There are two loads connected in parallel and powered from a 7200-V source. The first load is 50-kVA…

A:

Q: Why do we have horizontal and vertical lines in a breadboard, and what are the advantages of these…

A: The breadboard vertical lines and horizontal lines have no relation to do with Kirchhoff's and ohms…

Q: The current lo of figure shown below ww-

A: Apply KCL at Principal node we can easily find Io

Q: A 400 MVA synchronous machine has H₁ = 4.6 MJ/MVA and a 1200 MVA machine has H₂=3.0 MJ/MVA. The two…

A: It is given that: H1=4.6 MJMVA ,S1=400 MVAH2=3.0 MJMVA ,S2=1200 MVASbase=100 MVA

Q: KIRCHOFFS METHOD, KVL, SOLVE FOr I, FOR LO0P KLMNK2 K. T02 305h 40V 5V N30V 50 IOV M. Σ

A:

Q: In fast decoupled method, the strong coupling between the following is used, a. Q and V b. Pand V c.…

A: In high voltage transmission systems, the voltage angles between adjacent buses are  small but,  X/R…

Q: Manufacturers usually specify the impedances of machines and transformers in O Percent O Per-unit O…

A: Need to Find correct option

Q: A generator having emf 7sint Volts is connected in series with 8 Ohm resistor and an inductor of 2…

A:

Q: A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R…

A: In RL parallel connection branch resistor and inductor are connected in parallel with each other and…

Q: 1. Determine the current of each line and the neutral current and measure the total power supplied…

A: Given: 3 phase 4 wire star connected load ZR= 950 ohm resister in series with 3 H inductor ZB = 1950…

Q: What are the branch currents, 12 and 13?

A: The Circuit Diagram is given as:

Q: Use the information below to answer questions 24 un The voltage across and the current through a…

A:

Q: Explain what RLC circuits do and how they work including transformers, where applicable.

A: It is asked to explain what RLC circuits do and how RLC circuits can work including transformers…

Q: Quèstion 14 The point form of Ampere law is given by Curl(D) = J Curl(V) = I Curl(B) = I Curl(H) = J…

A: In this question we will write point form of amperes law...

Q: In capacitive AC circuit voltage is leading current O a. True O b. False

A: In the given questions we need to discuss about the properties of capacitor.

Q: Write a matrix equation that determines the loop currents. Also solve the system For loop currents…

A: From the circuit we can see that there are 5 meshes and we will apply KVL equation in each mesh by…

Q: 5. Obtain the symmetrical components of a set of unbalanced currents I,-1.3225º, I,-0.86z180º and…

A:

Q: 1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c…

A: we have to calculate capacitance.

Q: transferred conductively f

A:

Q: The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base…

A: In this answer let us try to find the base power used in order to get the given per unit impedance…

Q: 7. Three load units A, B, and Care connected in parallel and take currents that are respectively 11…

A:

Q: 1. Set up the circuit shown using a function generator for the source voltage Vs. Set the function…

A: Note: As per the policy we can solve only one question, please re-upload the remaining as a separate…

Q: The power factor of purely resistance circuit is Zero O Leading O Lagging O Unity

A:

Q: What is load curve

A:

Q: Two 300-VA parallel-connected transformers can supply a maximum load of a. 150 VA b. 300 VA C. 450…

A: Two 300 VA parallel connected transformer can supply a maximum load of, equal to the sum of their…

Q: Q5/C: Compare between Auto transformers and 2 winding transformers.

A: The transformer is a static electrical device in which is used to step up/down the current and…

Q: 1-Explain the principle of commutator in d.c generator. 2M O lwiofmanatic circuit and give tha it.

A: Find answer

Q: Two identical 460/230-V transformers are connected in parallel to a common load with impedance 10 +…

A:

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.