100-volt shunt motor is developing six hp while operating at an overallefficiency of 86%. The armature and shunt field resistances are 0.06 and 50 ohms, respectively. Determine stray power loss. Ans.: 378.41 W write all necessities, circuit diagram and step by step solution

100-volt shunt motor is developing six hp while operating at an overallefficiency of 86%. The armature and shunt field resistances are 0.06 and 50 ohms, respectively. Determine stray power loss. Ans.: 378.41 W write all necessities, circuit diagram and step by step solution

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 20hp, 240V, two-pole and 60-Hz, Y-connected wound- rotor induction motor. Its equivalent circuit components are Rj=0.260, R2=0.180, Xj=0.470, X2=0.480, Xm=15.60, Pmech=550W, Pcore=480W, and Pmisc=120W. For a slip of :0.045, find a) The stator copper losses PSCL and the air-gap power PAG b) The power converted from electrical to mechanical form Pconv c) The induced torque tind and the load torque tjoad d) The overall machine efficiency e) The motor speed
A Long Shunt Compound DC Generator supplies 90-amp at 120-volt. Series field resistance of 0.03-ohm, armature and brush contact resistance is 0.04-ohm, shunt field resistance of 46- ohm and compensating resistance of 0.009-ohm, the Iron and friction losses mount to 458- watts. Find the over all efficiency.
Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
i need the answer quickly
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If this DC machine is operating as a motor with rated flux at rated speed, calculate the rated torque (TR), rated current (IR), rated voltage (VR), efficiency (n) at the rated point, taking into account the winding losses. Find the speed (@NL) of this motor in no-load condition. TR Nm IR А VR V Eff = % ONL= rpm
The speed of a 230 V shunt motor is to be reduced from 900 r.p.m to 600 r.p.m. Theresistance of the armature circuit is 0.3 ohm. When the motor current is 30 A, speedis 900 r.p.m. If the current reduces to 20 A at lower speed, what arrangement shouldbe made? Neglect any effect not included in the data given. (Ans.3.833 ohms)
A 200 V dc shunt motor takes a current of 20A on a certain load. R= 12 and Rah= 2002. Find the resistance to be inserted in series with the armature to reduce the speed to 75% of its original value if the load torque is constant.
A shunt DC motor is operated at no-load at rated voltage 220 V, speed 1700 rpm and armature current 3.5 A. The resistance of the armature winding is Ra=0.39 , resistance of the field winding is Rf=137 0. Find the speed of the motor at rated load with armature current 43 A. *
(A Long shunt compounded DC motor has a nominal voltage of VT=100V. Its armature circuit total resistance is Ra= 3 ohm, serial field resistance Rs= 1 ohm. and shunt field resistance Rsh= 50 ohm . Find the shunt field circuit current (Ish) of the motor and write inside a box as given below, under rated load (full load) conditions. Draw the electrical equivalent circuit of the motor and write the resistance values of Ra, Rs and Rsh resistances on the correct places of the electrical equivalent circuit. Be careful about your solutions and drawings to be readable) Ish=?solve this question by using the rulers of Electromechanical Energy Conversion 2
A brushed DC motor is spinning at a maximum no-load speed of 6206 rpm. The nominal brush voltage drop is 0.67 V and the rated terminal voltage of the machine is 13 V. Determine the voltage constant, Ke, of the machine in Vs/rad.
A 550-volt long-shunt compound motor has armature an resistance of 0.815 ohm and a series field resistance of 0.15 ohm. The full load speed is 1,900 rpm when the armature current is 22 amp. (a) At what speed will the motor operate at no load if the armature current drops to 3 amp with a corresponding drop in flux to 88 per cent of the full-load value? (Assume a brush drop of 5 volts at full load and 2 volts at no load.) (b) Calculate the percent speed regulation of the motor.