A 480-V, 100-kW, 50-Hz, four-pole, Y-connected synchronous motor has a rated power factor of 0.85 leading. At full load, the efficiency is 91 percent. The armature resistance is 0.08 2, and the synchronous reactance is 1.0 2. Find the following quantities for this machine when it is operating at full load: (a) Output torque (b) Input power (c) n

A 480-V, 100-kW, 50-Hz, four-pole, Y-connected synchronous motor has a rated power factor of 0.85 leading. At full load, the efficiency is 91 percent. The armature resistance is 0.08 2, and the synchronous reactance is 1.0 2. Find the following quantities for this machine when it is operating at full load: (a) Output torque (b) Input power (c) n

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 107 hp, 257 V dc shunt motor has the magnetization curve in the graph. The armature circuit resistance, including brushes, is 0.032 ohm . no load rotational losses are 2077 W and the stray loss is 1% of the output The field rheostat is adjusted for a no-load speed of 1107 rpm a. What would be the field current at no load when speed is 1100 rpm b. Determine Specd and output in horsepower corresponding to an armature current of 400A c. Now a cumulative series turns 2 (Nse) per pole is to be added with Rse negligible and 1000 turns in Shunt field find speed corresponding to an armature current of 400A Mmf or shunt-field current, per unit 0.8 0.2 0.4 0.6 1.0 1.2 1.4 320 300 280 260 LO 240 220 200 0.8 180 160 0.6 140 120 100 0.4 80 60 0.2 40 20 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 Shunt-field current, A Magnetization curve for 257 V and 1207 rpm de machine Generated voltage, V Generated voltaoe. Der unit
A 10hp six-pole 60-Hz three-phase induction motor runs at 1090 rpm under full-load conditions. a)Determine the slip of the rotor currents at full load. b) Determine the frequency of the rotor currents at full load. c) Estimate the speed if the load torque drops in half.
A 220V DC shunt motor draws a no load armature current of 2.5A when running at 1400 rpm. Determine its speed when taking an armature current of 60A, if armature reaction weakens the flux by 3%.
A 3 phase , 6 pole , 400 V , 50 Hz , induction motor has R2= 0.1 ohm /ph , X2= 0.8 ohm /ph and the induced emf between slip rings at standstill is 160 V , Assume the friction losses is 300 W. find :- a) the torque output at slip =3% . b) critical slip and the torque maximum .
A 3-phase 50 Hz I.M. has a rated torque = 16.7 N.M and maximum torque = 40.5 N.M. If its rated speed = 910 R.P.M, the :speed at maximum torque will be %3D R.P.M 578.28O R.P.M 421.640 R.P.M 590.160 None O
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
16.A DC compound short-shunt motor draws a current of 50 A at a voltage of 220 V. if the armature resistance is 0.04 ohms, series field resistance is 0.01 ohms and shunt field resistance is 125 ohms. Knowing that the motor is rotating at 1200 rpm and has an efficiency of 90% calculate: a) back induced emf. b) Input power. c) Output power. d) Shaft torque. e) Copper losses. f) Iron losses. Ans. 217.57 V, 11 kW, 9.9 kW, 78.78 N.m, 503.54 W, 769.46 W
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
1. The rotor resistance and reactance per phase of a three-phase wound rotor induction motor are 0.035 and 0.15 ohm respectively. If an additional resistance is added, the starting torque is one half of maximum torque and the full load torque is three-fourth of the maximum. Determine the following: a. Full load speed b. speed at maximum torque c. value of additional resistance per required to achieve these conditions.
On full-load a 300 V series motor takes 90A and runs at 15 rev/s. The armature resistance is 0.1 ohm and the series winding resistance is 50 m.Determine the speed when developing full load torque but with a 0.2 ohm diverter in parallel with the field winding. (Assume that the flux is proportional to the field current.
Q15. A series-wound motor is connected to a d.c. supply and develops full-load torque when the current is 30 A and speed is 1000 rev/min. If the flux per pole is proportional to the current flowing, find the current and speed at half full- load torque, when connected to the same supply.