A 120-V shunt DC motor has armature resistance R,=0.2N and and field resistance Rp=602 . The rated full load current is 42 A. Calculate the following: (A) Calculate the following 1. The starting current if the motor is directly connected across the 120V supply. Express the current as a percentage of the full load value. 2. The value of the external resistance to be connected in series with armature circuit to limit starting current to 150% of the full load current.

A 120-V shunt DC motor has armature resistance R,=0.2N and and field resistance Rp=602 . The rated full load current is 42 A. Calculate the following: (A) Calculate the following 1. The starting current if the motor is directly connected across the 120V supply. Express the current as a percentage of the full load value. 2. The value of the external resistance to be connected in series with armature circuit to limit starting current to 150% of the full load current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the circuit please.
Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
I want the solution in the form of a table
Can you solve the question step by step clearly ?
A 220 V, 7 A, 1100 rpm DC shunt motor has armature and field resistance of 1.75 02 and 250 n respectively. The load torque can be assumed to be constant at rated value. What is the motor speed if a resistance of 70 is inserted in the armature circuit?
A 200 V dc shunt motor takes a current of 20A on a certain load. R= 12 and Rah= 2002. Find the resistance to be inserted in series with the armature to reduce the speed to 75% of its original value if the load torque is constant.
4. A shunt motor designed to operate at 115 V, has an armature resistance is 0.12 ohms and the motor is taking 60 A in armature current at full load. Determine the value of the external resistance to be inserted in the armature circuit so that the armature current shall not exceed twice its full load value at starting. A. 0.838 ohm C. 0.667 ohm B. 0.919 ohm D. 0.733 ohm
The current drawn by the 230 V DC motor of armature resistance 0.5 ohm and back emf 200 V is ?
A 550-volt long-shunt compound motor has armature an resistance of 0.815 ohm and a series field resistance of 0.15 ohm. The full load speed is 1,900 rpm when the armature current is 22 amp. (a) At what speed will the motor operate at no load if the armature current drops to 3 amp with a corresponding drop in flux to 88 per cent of the full-load value? (Assume a brush drop of 5 volts at full load and 2 volts at no load.) (b) Calculate the percent speed regulation of the motor.
1. The rotor resistance and reactance per phase of a three-phase wound rotor induction motor are 0.035 and 0.15 ohm respectively. If an additional resistance is added, the starting torque is one half of maximum torque and the full load torque is three-fourth of the maximum. Determine the following: a. Full load speed b. speed at maximum torque c. value of additional resistance per required to achieve these conditions.
An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KĘ = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax 2. Plot the following relationships: (i) Torque versus current (ii) Induced voltage versus speed 3. If the above motor is operated at 3000 rpm with a load torque of 0.15 N.m, determine the armature voltage
A 500 V DC shunt motor takes 4 A at no-load. The shunt field winding resistance and the armature winding resistance are 250 and 0.2 respectively. Find the efficiency when the motor draws a current of 10 A at full load.