10° Joxana C Ca 60° Jet stream path View A-A AY Turbine rotor Blade linear AY velocity 200 mm Q Search 16.3 Vane motion

Q: A sharp-edged orifice of 12.5 mm in diameter has a coefficient of discharge of 0.6 and is situated…

A: Diameter = 12.5 mm = 0.0125 m Coefficient of discharge = 0.6 Head = 1.8 m Density = 998 kg/m3…

Q: 1. A pipe bends through an angle of 90° in the vertical plane. At the inlet it has a cross-…

A: 1) Draw diagram of bend pipe

Q: A pelton wheel working under a head of 50 meters, develops 80 kW at 230 rpm. Calculate the diameter…

A:

Q: A single cylinder double acting pump has a cylinder diameter of 135 mm and a stroke of 270 mm. The…

A:

Q: 1. A pump pumping liquid propellant operates at 10,000 rpm. The volumetric flow rate through the…

A:

Q: Compute the force that must be applied to prevent the cart in the figure from accelerating. The…

A: Here, we will use impulse-momentum equation to find the force. The force that needs to apply will be…

Q: The mean radius of an axial flow reaction turbine is 2.6 ft. and the axial velocity is 25 ft./s. The…

A:

Q: 6) A screw jack is used to lift a mass of 500kg. The screw has a thread with a pitch of 8 mm. An…

A:

Q: . Two identical cylinders are applied in series as shown in Fig.2. The cylinder piston and rod…

A:

Q: Ql: Two water jets hit the bucket of Pelton turbine. The diameter of each jet is 270mm. The main…

A: The Pelton wheel is a tangential flow impulse turbine. In an impulse turbine, only the kinetic…

Q: 4- A Pelton wheel has a mean bucket speed of 10m/sec with a jet water flowing at the rate of…

A: Given:u=10 m/sQ=700 L/s =0.7 m3/sH=30 mθ=160°cv=0.98

Q: /A Pelton wheel has a tangential velocity of buckets of 15 meters/sec. the water is being supplied…

A: calculated the power produced by the wheel in watts.

Q: A 150 mm diameter penstock supplies water to a turbine under constant head of 30 m. a. Calculate the…

A: Given question belongs to the subject Fluid Machinery and can be solved using concepts of the…

Q: water which is to be drained completely. The exit pipe is exposed to the atmosphere. The distance…

A: given:hc=6mhB=1.2m

Q: An irrigation pump delivers water through a 6 - inches horizontal pipe flowing full at the outlet,…

A: If an object travels with constant velocity, then the motion of the object is said to be uniform…

Q: Water at a pressure of 300 kN/m flows through a horizontal pipe of 120 mm diameter with a velocity…

A:

Q: f the velocity of water is 15 meters/sec and the pressure is 120kPa on the discharge side of the…

A: Given:At discharge side of the pump:V2=15 m/sP2=120 KPaAt suction side of the pump:V1=5 m/sP1=80 KPa…

Q: Residents of a certain town are happy because a fountain is to be designed for the park. A nozzle…

A:

Q: Problem 4: Compute the specific speed for a pump operating at 1750 rpm delivering 12 000 gal/min of…

A:

Q: assume a flow of 1.7 m3/hr. the pressure readings are 0.1 bar at the bare pump and 0.3 at the…

A: assume a flow of 1.7 m3/hr. the pressure readings are 0.1 bar at the bare pump and 0.3 at the…

Q: In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target…

A:

Q: 4 mm drill holes in the large water tank causing water to flow out of the tank into a single…

A: Given:dia of hole, d=4 mmh=5 mangle of deflection, θ=180°

Q: A fireboat is putting out a blaze from a beach bonfire that got out of hand. If the nozzle angle is…

A:

Q: A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The…

A:

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft…

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost…

Q: 120 Q/ calculate the force excreted on the blade by the jet if the angle of deflection 120 and the…

A: Given data: - The deflection angle is θ = 120o. The velocity of jet is V1 = 30 m/s. The flow rate…

Q: Draw the right diagram for the problem. Show complete solution. Water at 60 F from a lake through…

A:

Q: A centrifugal pump is designed to operate at 1800 revolutions per minute and with a head of 55…

A:

Q: Propeller blades in aeroplane are 2 m long. when propeller is rotating at 1800 rev/min, compute the…

A: here for tengential velocity at the tip of the blade radius = 2 m. and Vt = 2*pi*R*N / 60 m/s

Q: A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a…

A: The dynamics of fluid flow is the study of fluid motion with the forces causing flow. The dynamic…

Q: eliver 70 cfm water. ca

A:

Q: Determine the number of the impellers required for a multi stage pump to lift 4200 litres/minute…

A: We have, Total head, H=185 m,  N=750 rpm, Ns=70 rpm Q=4200 litres/min=4200×10-360=0.07 m3/s

Q: A nozzle of diameter 20 mm at one end is used to eject water with a 20 m/s of designed velocity.…

A: Given data: The diameter of the nozzle at converged end is d1 = 20 mm. The designed velocity of…

Q: A water jet impacting a conical surface (as shown). Find the force of water on the cone. V 50° V…

A: To determine the force acting on the conical surface.

Q: Q.1). The figure below shows a smooth curved vane attached to a rigid foundation. The jet of water,…

A:

Q: A Pelton wheel has a mean bucket speed of 10 meters per second with a jet of water flowing at a rate…

A:

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.