Residents of a certain town are happy because a fountain is to be designed for the park. A nozzle diameter of 50 mm is chosen and the water velocity at the nozzle will be 8.5 m/s. (a) Calculate the height (m) to which the water will rise. The jet passes through a circular opening 2 m above the nozzle. (b) Calculate the diameter (mm) of the opening so that the jet just passes through without interference.

Residents of a certain town are happy because a fountain is to be designed for the park. A nozzle diameter of 50 mm is chosen and the water velocity at the nozzle will be 8.5 m/s. (a) Calculate the height (m) to which the water will rise. The jet passes through a circular opening 2 m above the nozzle. (b) Calculate the diameter (mm) of the opening so that the jet just passes through without interference.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is delivering 160 liters per second of water using an impeller diameter of 254mm and operating at a speed of 1800 rpm. If the speed is held constant and the impeller diameter is changed to 203.2 mm, what is the new discharged of the pump in liters per second?(128 L/s)
Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C is 7.5 cm in diameter. If the flow in A is divided as follows 2/3 goes to B and 1/3 goes into C, what is the discharge in pipe A, if the velocity must not exceed 3 m/s in any of the pipes. Include free body diagram.
6.7. Calculate the force exerted by the water on this orifice plate. Assume that water in the jet between orifice plate and vena contracta weighs 4.0 lb. 0.75 0.20 10' d
A water flows through a 2-in opening in the side of a tank. If the opening is 8 ft below the surface of the water, what volume of water would escape from the tank per minute?
Consider a pressure washer exerting a horizontal force on the wall (and the operator). Assume that water enters the pressure washer wand vertically. Output nozzle is 1/8" (0.125 inches) in diameter. A. What is the water pressure at the exit (once water leaves the nozzle)? b. Calculate the flow needed to produce 20lb of horizontal force.
5.2 The head of water at the inlet of a pipe of length 1 500 m and diameter 400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to the pipe. Find the velocity of water at the outlet of the nozzle if ƒ = 0.01 for the pipe.
Do all the parts
Subject : Mechanical engineering ,Fluid mechanics. Question: A stream of water 75 mm in diameter discharges into the atmosphere at a velocity 24.4 m/s. Find the power in the jet using the datum plane through the center of the jet. Answer is 33 kW
Water flows out of 5 mm x 200 mm slots in a sprinkler as shown. The mass flow rate is 15 kg/s. 200 mm 250 mm a. Find the torque required to prevent the sprinkler from rotating. b. Find the rotation rate of the frictionless sprinkler when released.
Hello Expert, Please assist with this Fluid Mechanics Question. Kindly answer correctly and show ALL the steps. Thanks in advance
A horizontal jet of water 2x103 mm2 cross-section and flowing at a velocity of 15 m/s hits a flat plate at 60o to the axis (of the jet) and to the horizontal. The jet is such that there is no side spread. If the plate is stationary, calculate a) the force exerted on the plate in the direction of the jet and b) the ratio between the quantity of the fluid that is deflected upwards and that downwards. Assume that there is no friction and no shear force.