10-65. The shaft is made of 12 tool steel, has a diameter of40 mm, and is fixed at its ends A and B. If it is subjected tothe torque, determime the maximum shear stress in regionsAC and CB.2 kN-m600 mmB00 mim

Given, L1 = 800 mm = 0.8 m L2 = 600 mm = 0.6 m D = 40 mm = 0.04 m r = d/2 = 0.04/2 = 0.02 m Torque…

Answered: 10-65. The shaft is made of 12 tool…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.30P: Solve Prob. 7.29 if =0.

See similar textbooks

Similar questions

PI0-2. Determine the internal torque at cach section and show the shear stress on differential volume elements located at A, B, C, and D. 400 N-m 600 N-m
10-1. The solid shaft of radius r is subjected to a torque T. Determine the radius r' of the inner core of the shaft that resists one-half of the applied torque (T/2). Solve the problem two ways: (a) by using the torsion formula, (b) by finding the resultant of the shear-stress distribution.
FI0-R. The gear motor can develop 2250 W when it turns at 150 rev/min. If the allowable shear stress for the shaft is Talom = 84 MPa, determine the smalest diameter of the shaft to the nearest mm that can be used.
*10-76. The two l-m-long shafts are made of 2014-T6 aluminum. Each has a diameter of 30 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B. They are also supported by bearings at C and D, which allow free rotation of the shafts along their axes If a torque of 900 N-m is applied to the top gear as shown, determine the maximum shear stress in each shaft. 900 N-m 80 mm 40
10-39. The 60-mm-diameter shaft is made of 6061-T6 aluminum. If the allowable shear stress is Talo - 80 MPa, and the angle of twist of disk A relative to disk Cis limited so that it does not exceed 0.06 rad, determine the maximum allowable torque T. 1.20m 120m
The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the three torques, determine the absolute maximum shear stress in the shaft. The smooth bearings A and B do not resist torque.
10-2. The solid shaft of radius r is subjected to a torque T. Determine the radius r' af the inner core of the shaft that resists one-quarter of the applied torque (T/4). Solve the problem two ways: (a) by using the tarsion formula, (b) by finding the resultant of the shear-stress distribution. т
10-22. If the geans are subjected to the torques shown, determine the maximum shear stress in the segments AB and BC of the A-36 steel shaft. The shaft has a diameter of 40 mm. 300 N-m 100 N-m 200 N-m
The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the three torques, plot the shear stress distribution along a radial line for the cross section within region CD of the shaft. The smooth bearings at A and B do not resist torque.
10-6. The solid 30-mm-diameter shuft is used to transmit the torques applied to the gears. Determine the absolute maximum shear stress in the shaft. 00 N-m S00N-m 200 N-m 400 N-m 300 mm 400 mm S00 mm
10-59. The A-36 hallow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at 80 rad/s, it transmits 32 kW of power from the engine E to the generator G. Determine the smallest thickness of the shaft if the allowable shear stress is Talle - 140 MPa and the shaft is restricted not to twist more than 0.05 rad.
If the gears are subjected to the torques shown, determine the maximum shear stress in the segments AB and BC of the A-36 steel shaft. The shaft has a diameter of 40 mm.

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L