10-15. Water in the concrete detention pond is to be pumped over the berm and into the lake. If the 8-in. diameter hose has a roughness of e- 0.0006 ft, determine the power output of the pump so that the flow out of the pipe is 2400 gal/min. The hose is 800 ft long. The water temperature is 60'F.

Q: • Pump (or turbine) efficiency = Power Out / Power In • Schedule 40 steel and PVC pipe have the same…

A: a) Calculating the head pump delivery: hpump=∆Pγhpump=128 psi×114 in2ft262.4 lb/ft3hpump=295.38 ft

Q: erature is 40°F, what is the head loss sthf=57.5t, wh

A: Discharge = 2 cfsDiameter of the pipe = 6 inch.Water Temperature = 40 deg FHead Loss in 1000 ft pipe…

Q: Q2-a) A sand filter 3 m x 1.2 m x 1.5 m (length x width x height) in size is connected from the long…

A: Size of filter = 3 m x 1.2 m x 1.5 m ( L x B x H ) Water level in tank above the mean level of the…

Q: Same elevation - Water T-10°C Machine A

A:

Q: Q6:For the temporary cofferdam shown below .k-4.3 10 m/sec and length of coffer dam -10m ,find the…

A:

Q: maintained at the summit, where the pipe is 90 m above 3.0 J/N between the reservoir and the summit.…

A: Given:-

Q: bject: Dete: he wat er level in a tank iS 20m above the giound. A hose is connected to the Dotton of…

A: Given data  Depth of water Height of water jet To find Pump minimum pressure

Q: A Francis radial-flow turbine has a runner inlet radius of 2.75 m and its outlet radius is 1.85 m.…

A: The given data is shown below: Inlet radius=2.75 mOutlet radius=1.85 mInlet width=0.9 mOutlet…

Q: An engineer was task to compute for the minimum pump power in horse power. The following are the key…

A:

Q: A fire pump delivers water through 15 cm main pipe to a hydrant to which is connected an 8 cm hose,…

A:

Q: Compute the pressure at the water pipe. 2.0m -Sen water (Sg - 1.05) 2.7m 2m 1.5m meraury sg-2.1

A:

Q: 6. A galvanized iron pipe is required to carry water at a discharge of 3.5 cfs and with a head loss…

A:

Q: 8 a lonj 191 to o S

A:

Q: The diameter of a 250m long PVC pipe is to be selected. The pipe is required tocarry a discharge of…

A: The objective of the question is to determine the diameter of a PVC pipe that can carry a specific…

Q: A pump is delivering water at atmospheric pressure to an elevation of 400 m. Elevation of the pump…

A:

Q: The tidal turbines are placed.. O a. Under the sea water O b. Under the ground O c. On the ground O…

A: Tidal turbines are like similar to that wind turbines which is used to generate power  Tidal…

Q: A tank filled with water at 30°C is supplies water for a shower based on gravity driven flow. The…

A: The given data is shown below: Temperature=300CDiameter=1.5 cmCoefficient of exit loss=0.5Flow…

Q: 10-26 If a flow of 3 cfs of water is to be maintained, what power must be added to the water by the…

A: This question belongs to subject fluid mechanics. In this question find out power added to the water…

Q: Water (60°F) is running through Schedule-80 PVC pipe whose size changes gradually from 6-in nominal…

A: To solve this problem, we can use the Bernoulli equation, P + 1/2 * ρ * v² + ρ * g * z =…

Q: Fluid Mechanics II Dr. Basim Al-Zaidi June 27, 2020 El. 200 mA A Res. H-W Pipe B pipec Pipe E…

A: For all pipes, L = 600 m d = 500 mm or 0.5 mf = 0.03Head added by pump = 15 m Velocity in pipe C = 5…

Q: An inward flow reaction turbine has external and internal diameter as 1m and 0.5m respectively. The…

A: Given data in question  External and internal Diameter 1 m and 0.5 m Velocity 1.5 m/s To find out…

Q: Vater is supplied at 170 ft³/s and 71 psi to a hydraulic turbine through a 3-ft inside-diameter…

A:

Q: Problem 7 72 Air at 1500 kPa absolute flows in a 25-mm-diameter tube. maximum laminar flow rate. Use…

A:

Q: The pump has to draw 0.7 m³/s flow to the pipe at an elevation of 10 m where a pressure p = -88.29…

A:

Q: A 1000-ft-long 2-ft-diameter concrete pipe (sharp-edge entrance) is used to convey 60°F water from…

A:

Q: 1. For a maximum expected flow rate of 30 I/s of water. A diameter of 0.2 m is placed. The material…

A: Given data:- Diameter of pipe, d = 0.2 m Length of pipe, L = 250 m Temperature of water, t = 10° C…

Q: Determine the discharge and compute the power consumption. (Neglect all minor losses.) A Q eff PUMP…

A: D = 0.2 m  f = 0.02 k = 10

Q: 4.2.11. A pump is needed to convey 8 cfs of water at 68°F through a 130-ft-long horizontal, ductile…

A: Detailed explanation:Final values might differ a little bit due to calculation done by…

Q: A rectangular area 900 m long and 400 m wide is required to be irrigated. The soil to be irrigated…

A:

Q: b) Engine oil (p = 888 kg/m', u = 0.8374 kg/m.s) in a reservoir is being discharged into the…

A: Given  Density of oil= 888 kg/m3  Dynamic viscosity= 0.8374kg/ms

Q: 9 ViscoSity a long ye and equal to c

A:

Q: 8) A 5.9866 cm-diameter water jet with V-45 m/s, strikes a moving blade with V₁-15 m/s. The power…

A: Given data:   Diameter of water jet=5.9866 cm Velocity of jet=45 m/s Velocity of blade=15 m/s   It…

Q: Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min…

A:

Q: 8-42E Water at 60°F passes through 0.75-in-internal- diameter copper tubes at a rate of 1.2 lbm/s.…

A: Diameter of copper tube = 0.75 in Mass flow rate = 1.2 lbm/s   To determine the pumping power,P per…

Q: 9.) A fire pump delivers water through a 300-mm-diameter main to a hydrant to which is connected a…

A: A fire pump is given Which delivers water through 300mm diameter main to hydrant which is connected…

Q: The power input per unit volume for a flash mixer of volume 3 m³ is 600 W. Assume dynamic viscosity…

A:

Q: A Reg.No-m length of smooth horizontal pipe is attached to a large reservoir as shown in Fig. 2. A…

A: Given:- The length of smooth horizontal pipe = Reg. No m = 5350 m  The flow rate at which water gets…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.