1.8 Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (a.) are shown in the figure.

Q: Define hydrostatic stress state.

A: Solution: It is defined as the state in which stresses of the same magnitude and direction are…

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: What is section modulus?

A: The section modulus helps to calculate the outermost stress in the beam section. It is numerically…

Q: The diameter of the cylinder in a scrap baling press is 150 mm. The stroke of the cylinder is 2.5…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Warning-If not anything upto the mark, I'll report and dislike you. Draw figure of uniaxial state of…

A: Uniaxial State of stress-  this type of stress has only one principal stress. ie , when an object is…

Q: can someone draw figure for this based on the solution given

A:

Q: Please use maximum shear stress theory

A:

Q: Write the formula used to determine the average shear stress?

A: shear stress is the stress produced due to shear force.

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: Mr. Ahmed want to buy pump bodies for his company, he selected the gray cast iron as a material…

A: Solution:

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The above statement is false.

Q: Use Archimedes' principle on any case study in contextual engineering applications. Calculate its…

A: Given question: Use archimedes' principle on any case in contextual engineering applications.

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: 70 in Hg abs = psig

A: 70 in Hg abs

Q: What would be the critical path and the project duration for M?

A: The network diagram has activities from A to M and different time intervals are given.

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: Assume oz = 500, ay = 300, Txy = 250, oyicld = 350. Answer the following questions. Click here for…

A: GIVEN DATA σx= 500MPa σy= 300MPa τxy= 250MPa We have to find maximum and minimum normal stress on a…

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A: At sea levelThe diameter of ballon d=8 indensity of air ρ=0.07498 lb/ft3Pressure P=14.7 psiawhen…

Q: Q3/ Determine the resultant of the force system with respect to the point (A)

A:

Q: Describe the hydrostatic stress?

A: When a force is imparted on a body, an internal resisting force is set up into the body, impeding…

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: Write the flexure formula?

A: Flexure formula This formula is used to determine the internal bending stress when an external force…

Q: Maximum Stresses in Thick Walled Cylinders

A: To determine the maximum radial and tangential stress for the thick walled cylinder

Q: What is the ideal column?

A: An ideal column is one that is perfectly straight, made of a homogeneous material, and free from…

Q: DIFFERENTAITE SHEAR STRESS FROM SHEAR STRAIN. THEIR RATIO

A:

Q: 6. Three reservoir A, B and C are connected respectively with pipes 1,2 and 3 joining at a common…

A: Given:The elevation of the common junction D, The elevation of the reservoir A, The elevation of the…

Q: Write the nature of work done by an elongated spring?

A: The elongation produced in an ideal spring is directly proportional to the spring force F=−kx.

Q: 1- Metals is more - --than ceramic in this property. 2- The engineering design deals with ----and 3-…

A: Dear Student, As per the Bartleby answering guidelines we are supposed to answer first 3 questions.…

Q: 1- A mold with dimensions of 3 cm x 15 cm x 8 cm is intended in a sand plumbing through an estuary…

A: GIVEN: Dimension of mold = 30cm×15cm×8cm. length of estuary= 8cm Area of gate or entrance = 3cm2…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.