Answered: 1.5 m -1.25 m- 2 m 60° Prob. 9-129

Engineering

Civil Engineering

1.5 m -1.25 m- 2 m 60° Prob. 9-129

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The cross section is elliptical as shown in the figure and the uniform thickness t=5mm The…

A: Given, Internal Pressure, P = 1.4 MPaThickness, t = 5 mmRadius, r = 0.15 m = 150 mm Circumferential…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Moment at given section due to load PM1=1500×150=225000 N.mmMoment at given section due to load…

Q: The members of the mechanism are pin connected. If a vertical force of 800 N acts at A, determine…

A: Draw FBD:

Q: Consider the gravity dam (Figure 2) whose concrete density is noted Pb. The vertical dam profile has…

A: Dam height, hb = 30 m Dam width, lb = 44 m Dam length, Lb = 25 m α = 650 β = 450 Find:

Q: A tri-metallic bar is uniformly compressed by an axial force P = 40 kN applied through a rigid end…

A: Calculate the compressive stress in the copper tube in MPa.

Q: Question 14 of 15 The cross-sectional area of a column is in the shape of two concentric circles…

Q: 1380 N 800 N 1.8m1.8m A 25° 1.5m 2.1m

Q: 3.8 m 4.6 m (1) C 5.6 m (2) 3.3 m B

Q: An L-shape gate AOB weighing 20 kN at its center of gravity G, 0.6 m above the bottom and 0.5 m from…

A: Moment due to F1 force and load W about O will be clockwise and moment due F2 force will be…

Q: A 40-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

Q: A 4 m long quarter clrcular gate of radius 3 m and of negligible weight is hinged about Its upper…

Q: +. -y = 10 kN/m3 50 cm 7 = 20 kN/m3 3 10 cm 50 cm

A: considering atmospheric as zero..i.e.. calculating gauge pressure sign convention moving vertically…

Q: 2. A 10m high cantilever wall separates water and oil as shown. The water and the oil are 8m and…

A: To find support reaction

Q: (a) Determine the reactions at A and E if P = 800 N. The reactions are positive if to the right or…

Q: Locate the centroid of the homogeneous solid formed by revolving the shaded area about the z axis.

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: An open rectangular tank is 2 m wide and 9 m long. The tank contains water to a depth of 2 m and oil…

Q: A flow of a viscous fluid with μ = 1.0 u a velocity distribution given by u = The shear stress at y…

A: velocity distribution = 0.9y - y2To Find :The Shear stress at y = 0.45 m

Q: 1. A barrel in the form of a frustum of a cone with a radius of 3m at the bottom and 6m at the top.…

A: Density of oil = 0.85*1000 = 850kg/m3

Q: 30 0.9 m 1.2 m •At depth h the pressure is pgh. •Force on a small element = pressure x area

A: To determine hydrostatic pressure force on submerged plate. Given, Angle between the plate and the…

Q: Determine the axial stress in rod (1).

Q: B 0.75 m 55⁰ A 1 m 0.5 m 50 N 75 N-m

A: Given values: Consider the given structure and draw the free body diagram to calculate the unknown…

Q: Two solid cylindrical rods support a load of P = 33 kN as shown. Rod (1) has a diameter of 15 mm,…

A: P=33 kNrod 1 diameter = 15 mmrod 1 diameter = 12 mmTo find:Axial stress in rod 1

Q: A steady, two dimensional, incompressible flow field is represented by u = x + 3y + 3 and v = 2x - y…

A: Given- flow fields-u=x+3y+3v=2x-y-8

Q: 85 MPa B 66 MPa 65° 28 MPa A

A: We will use equations for principal stresses.

Q: 4.In turbulent flow the particals moves in all directions and randomly mixes with each other. O true…

A: Turbulent flow is a type of fluid (gas or liquid) flow in which the fluid undergoes irregular…

Q: The kinematic viscosity of the oil filled between two concentric vertical 150 mm long cylinders is…

A: Given data in question Length 150 mm Diameter 0.2 m Kinematic viscosity Specific gravity of oil…

Q: What is the equations for static equilibrium? * ΣFx 0 ΣFy -0 ΣFz 0 EMz = 0

A: Equations of static equilibrium - These are the equations developed, considering all the forces and…

Q: Problem #1: в (m) 800 + A (N) 200 + Y (N/m) 2 m \60° B 1. Determine the horizontal reaction at A.…

A: 1. Determine the horizontal reaction at A. 2. Determine the vertical reaction at A. 3. Determine…

Q: A tri-metallic bar is uniformly compressed by an axial force P = 40 kN applied through a rigid end…

Q: A 20mm diameter steel wire 150m long, is suspended vertically from one end. It supports a tensible…

A: The diameter of the wire is d=20 mm. The length of the wire is l=150 m. The load is P=20 kN. The…

Q: The face of a vertical dam has the shape of an isosceles triangle of altitude 4 m with an upper base…

A: Solution

Q: c) Calculate the vertical reaction at support B. When sketching FBD, assume the positive direction…

Q: ... А 30° 2.5m Water hinge L = 2m In the figure shown, a quarter circle gate AOB is hinged at point…

Q: 7. Determine the magnitude of the resultant force acting at A. 2 im a- 600 N 3.5 m 0.5 m Fc-450 N…

A: To find resultant force

Q: Find the capillary rise ( h) in the tube shown in the figure for a water-air-glass interface with 9=…

Q: Show a complete solution. Classify each of the structures as statically determinate or…

A: To classify the each structure-

Q: A closed tank has several layers of liquid and a circular bottom. a. Determine the hydrostatic force…

A: Pressure acting at the bottom of first fluid from the free surface, P1 = ρ1gh1 ρ1 = Where 1000 ×…

Q: Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of…

Q: Q2: Non rotating beam shown in the (fig.2), (F=100 lb), find the maximum stress and its location.…

A: Finding out maximum stress and it's location.

Q: In the following structure, bolt B has a diameter of 1.75” and bolt A has a diameter of 2.50”. Bar…

Q: Problem #5: X (N/m) Y (N/m) В - 3 m 3 m 14. Determine the reaction at A. (N) | 15. Determine the…

Q: 1. The rigid gate with 3m width is installed in order to control the water outflow as shown in the…

A: Given Width of gate = 3m Hinge is located 4 m below the top level

Question

Determine the magnitude of the resultant force acting on the gate ABC due to hydrostatic pressure. The gate has a width of 1.5 m. _ρw = 1.0 Mg/m³.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Trending now

This is a popular solution!

Step by step

Solved in 9 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

complete also the table
2. Find the hydrostatic force on the gate A if the gate is trapezoidal with a 2m upper base and 3 m lower base. 2 m S = 0.9 4 m S= 0.7 A 3 m S = 0.8 2 m
asap
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°
F 30° 0.5 m C 30° t 0.5 m B A 0.15 m 0.26 m The smooth pipe rests against the opening at the points of contact A, B, and Cand supports the forceF = 300 N. Neglect the pipe's thickness in the calculation. (Figure 1). Determine the magnitude of the reaction at A. and Determine the magnitude of the reaction at B.
SITUATION. Consider the figure shown below, neglect the self-weight of members AB and BC. 2.0 m E B +0.9 m-0.9 m- W=5.4 KN → Zoom image Determine the vertical reaction at C. ic 0.8 m 0.4 m
Draw the influence lines when a = 3 b = 3 c = 2 d = 2
Gate AB in the figure below is 1 m long and 0,7 m wide. Determine the force (F) on the gate and the position x, the centre of pressure. 3m Oil (sp gr = 0.81) ㅗ 1m. 7m 1m 1
Gate AB in the figure is 1.2 m wide and hinged at A and kept closed by a stop at B. Gage G reads 14.86 kPa. Oil has a specific gravity of 0.76. Determine the total hydrostatic force acting on the gate in (kN), Determine the location of the total hydrostatic force from the hinge in (m), Determine the reaction at the stop in (kN)
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°
4. An upright wine barrel contains 3 m depth of wine with relative density of 1.015. The barrel is 2 m in diameter and 4 m high. Since the barrel is closed, there is a pressure of y kPa (where y = 60 above the liquid surface. (a) Draw the free-body diagram of the barrel. (b) What is the total normal force in kg acting on the wall of the barrel? (c) What is its location from the ) due to air that fills the container bottom of the barrel in meters?